manualshive.com logo in svg

Kodak HEALTH SCIENCES X-Omat Clinic 1, Руководство по установке

Поделиться
Скачать
Kodak HEALTH SCIENCES X-Omat Clinic 1 Скачать руководство пользователя страница 9

Installing the PROCESSOR

981088 – September 1995

9

Important

• Servicing and accessing the PROCESSOR is easiest if you position the PROCESSOR on a Kodak

M35, M43, Clinic 1 MOUNTING STAND.

• If you will not be installing the PROCESSOR on the Kodak M35, M43, Clinic 1 MOUNTING

STAND, see “Installing the PROCESSOR on a Table Top” on Page 12.

• If you will be installing the PROCESSOR through the darkroom wall, see “Installing the

PROCESSOR Through the Wall” on Page 13.

[2] Install the PROCESSOR by following 1 of the 3 procedures outlined on the following pages:

• on a Table Top — see Page 12

• through the wall — see Page 13

• on the M35, M43, Clinic 1 MOUNTING STAND — see below

[3] If you removed the INTERLOCK SWITCH in Step 1a, do the steps below.

(a) Install:

• SIDE ACCESS PANELS

• FRONT ACCESS PANEL

• TOP COVER

(b) Push the MOUNTING BRACKET forward until the BLADE of the TOP COVER fully engages the

INTERLOCK SWITCH.  Tighten the 2 SCREWS to secure the BRACKET.

Installing the PROCESSOR on the MOUNTING STAND

[1] Place the PROCESSOR on the MOUNTING STAND with the large holes toward the operator’s work area.

Important

If you will be securing the MOUNTING STAND with SEISMIC BRACKETS, ensure that the MOUNTING
STAND, on its LEVELING FEET, is no more than 2.5 cm (1 in.) above the floor.

[2] Install the 4 LEVELING FEET and 4 LOCK NUTS on the MOUNTING STAND.

(a) Rotate the LEVELING FEET until the MOUNTING STAND is approximately 2.5 - 3.75 cm

(1 - 1

1

⁄

2

in.) above the FLOOR.

Important

If you will be securing the MOUNTING STAND with SEISMIC BRACKETS, use the FLOOR PLATES provided
with the SEISMIC BRACKET KIT 261413.

[3] Install the FLOOR PLATES under each of the 4 LEVELING FEET of the MOUNTING STAND.

[4] Move the MOUNTING STAND as close to its final position as possible while still maintaining clearance on

all sides of the PROCESSOR for access to components.

[5] Check that the MOUNTING STAND is level both front-to-back and side-to-side.

[6] Once the MOUNTING STAND is level, tighten the 4 LOCK NUTS against the base of the MOUNTING

STAND to secure its height.

Содержание HEALTH SCIENCES X-Omat Clinic 1













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды