manualshive.com logo in svg

Kodak HEALTH SCIENCES X-Omat Clinic 1, Руководство по установке

Поделиться
Скачать
Kodak HEALTH SCIENCES X-Omat Clinic 1 Скачать руководство пользователя страница 75

Final Checkout

981088 – September 1995

75

Note

• If you are increasing the dryer setpoint temperature, the READY INDICATOR will illuminate and

the WAIT INDICATOR will turn off once the DRYER has reached the new setpoint temperature.

• If you are decreasing the dryer setpoint temperature, the WAIT INDICATOR will not illuminate

when the DRYER has reached its new setpoint temperature.  Therefore, allow 5 minutes after
decreasing the dryer setpoint temperature for the DRYER to reach its new setpoint temperature.  If
you insert a sheet of film too soon, the DRYER will warm up and not cool down.  This may cause
some erratic results.

• The PROCESSOR may enter standby mode while you are making adjustments to the DRYER.

[3] Examine how the sheet of film feels to the touch as it exits the DRYER ASSEMBLY.  The film should feel

cool and be dry.

• If the sheet of film is wet or cold when it exits the DRYER ASSEMBLY:

– turn the DRYER TEMPERATURE CONTROL KNOB clockwise

two detent positions

• If the sheet of film is damp or tacky when it exits the DRYER ASSEMBLY:

– turn the DRYER TEMPERATURE CONTROL KNOB clockwise

one detent position

• If the sheet of film is dry and hot when it exits the DRYER ASSEMBLY:

– turn the DRYER TEMPERATURE CONTROL KNOB counterclockwise

one detent position

[4] Repeat Steps 2 and 3 to achieve the correct adjustment.

[5] Check film quality by running exposed test films.

[6] Perform operator training.

Publication History

Print Date

Pub.

No.

ECO No.

Affected

Pages

File Name

Notes

Jan. 1994

981088 2622-064

All Pages

3229ii_d.txt

1st Printing

March  1994 981088 2622-082

Front Cover, 3,
69, 83,
Back Cover

3229ii_d_082.txt

April  1994

981088 2622-085

Front Cover, 3,
42, 52, 60, 61,
65, 79, 80, 83,
Back Cover

3229ii_d_085.txt

Added DC Interlock Switch S6

May 1994

981088 2622-098

Front Cover,
6, 15, 19, 83,
Back Cover

3229ii_d_098.txt

Removed Packing List.
Corrected Dimensions in
Through-the-Wall Illustration

Oct. 1994

981088 2622-117

All Pages

3229ii_d_117.txt

Major Revision and Update to
Bring Manual to Final Release
Status

01SEP95

981088 2622_157

All Pages

ii3229_3_01sep95.doc

Revision due to product
changes; reprinted entire
manual due to new publication
software used for
documentation

Содержание HEALTH SCIENCES X-Omat Clinic 1













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды