manualshive.com logo in svg

Kodak HEALTH SCIENCES X-Omat Clinic 1, Руководство по установке

Поделиться
Скачать
Kodak HEALTH SCIENCES X-Omat Clinic 1 Скачать руководство пользователя страница 47

Leveling the PROCESSOR

981088 – September 1995

47

Section 7: Leveling the PROCESSOR

Important

• Leveling the PROCESSOR correctly will ensure:

– the correct flow of the processing solutions

– the correct transport of the film

– the correct fit of all ACCESS PANELS

• If you plan to secure the MOUNTING STAND to the floor, level the PROCESSOR before you install the

SEISMIC BRACKET KIT 261413.

• If you are installing the PROCESSOR on the MOUNTING STAND and are securing the PROCESSOR to the

MOUNTING STAND, do the following steps using the LEVELING FEET for the MOUNTING STAND and
not the LEVELING FEET for the PROCESSOR.

• Be sure that the PROCESSOR is in its final location before leveling it.

[1] Check that the DEVELOPER and FIXER RACKS are seated firmly.

[2] Place a LEVEL first front-to-back and then side-to-side across the RACKS.  Check that both ends of the

RACKS are level.

Figure 40

Placing the LEVEL on the RACKS

H130_0107HA

H130_0107HCA

FIXER RACK

LEVEL

DEVELOPER
RACK

Содержание HEALTH SCIENCES X-Omat Clinic 1













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды