Kikusui PWX1500H Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 131

background image

PWX

81

Master-Slave Parallel Operation

Parallel

/Series Operation

4

Connecting the load (parallel operation)

1

Turn off all the PWX series that you want to connect in parallel.

2

Remove the OUTPUT terminal covers.

3

Connect the load cables to the output terminals of the master unit and
the slave units.

4

Connect the load cables of the master unit and slave units to the load
through a relay terminal block.

Use load cables that have sufficient current capacity. Use load cables of equivalent
length and cross-sectional area to connect each power supply to the relay terminal
block, and wire the cables so that they are as short as possible (50 cm or less). Also,
make the connection from the relay terminal block to the load block as short as possi-
ble.

Wire the J1 connector signal cables and the load cables as far apart as possible.

5

Connect the output terminals (positive or negative) of the master unit
and the slave units to the chassis terminals.

Connect the same polarity output terminals on the master unit and slave units.

If you are using the units under floating conditions, do not connect the terminals.

WARNING

Risk of electric shock. Turn the POWER switch off before you touch the OUTPUT ter-
minals. Attach the OUTPUT terminal cover after you finish wiring the load.

CAUTION

• When you connect the output terminals to the chassis terminals, be sure to connect the

same polarity output terminals (positive or negative) of the master unit and the slave units
to the chassis terminals. If you connect different polarity output terminals of the master unit
and the slave units to the chassis terminal, the output will be grounded through the power
cable’s GND wire. Not only will this make the output incorrect, it will also cause the chassis
terminal cable to burn out.

• When the load cables are distributed over longer distance, the phase shifting due to wiring

inductance and capacitance may go beyond the limit and result in oscillation. To prevent
such oscillation, connect an electrolytic capacitor with several hundreds to several tens of
thousands

μ

F across the load.

Use an electrolytic capacitor that has a withstand voltage that is at least 120 % of the prod-
uct’s rated output voltage.

• Twist the positive and negative cables together, and make the connection to the load as

short as possible. Oscillation may occur as a result of wiring inductance.

Relay terminal
block

Load

Master unit

Slave unit 1

Slave unit 2

Output terminal

Chassis terminal

Output terminal

Chassis terminal

Output terminal

Chassis terminal

Load connections
for parallel opera-
tion (two slave
units)

See

«
...
79
80
81
82
83
...
»

Содержание PWX1500H




































































































































Отзывы:

Нет отзывов

Похожие инструкции для PWX1500H

Бренд: FASTER TOOLS Страницы: 12

BANDSAW BLADE SHARPENER

Бренд: Woodland Mills Страницы: 56

Бренд: Image Industries Страницы: 32

Бренд: Oben Страницы: 32

Бренд: YATO Страницы: 72

Бренд: Ayce Страницы: 59

Millipore mA700

Бренд: Merck Страницы: 9

Бренд: HB-THERM Страницы: 3

Бренд: Huck Страницы: 26

MTL 9492-PS-PLUS

Бренд: Eaton Страницы: 24

Бренд: Magnetek Страницы: 34

Бренд: Palmer Страницы: 16

Бренд: Facom Страницы: 62

HEAVY DUTY M12 FTB

Бренд: Milwaukee Страницы: 77

Explorer 100 Plus

Бренд: Jackery Страницы: 45

Бренд: BluePoint Fasteners Страницы: 13

Бренд: HIOS Страницы: 12

Trix Minitrix 60041

Бренд: marklin Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды