Kikusui PWX1500H Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 131

background image

50

PWX

CONFIG Settings

CF19 Current and power display on slave units for master-slave
parallel operation

Sets whether the current or power on slave units is displayed during master-slave parallel
operation. You can display and specify this parameter only when the PWX series is being
used as a slave unit.
If this parameter is set so that the current or power on slave units is not displayed, the amme-
ter displays

”

----.

”

CF20 LAN interface parameter

Sets whether the LAN interface will be used.
By setting it to “oFF,” you can disable the LAN interface function even when a LAN cable is
connected. You will also not be able to set the LAN interface parameters.
Even when this is set to “on,” if the command language is set to legacy (CF21: LGCy), you
cannot use the LAN interface.
This parameter is applied when you turn the POWER switch off and on.

CF21 Command language parameter

Sets the command language that is used in remote control messages.
This parameter is applied when you turn the POWER switch off and on.

CF22 Emulation parameter during remote control

Sets the emulation that is used during remote control. If you have set the command language
to legacy languages, you can only select “Gen” or “PAG.”
This parameter is applied when you turn the POWER switch off and on.

Value

Parameter description

oFF

The current or power of slave units is not displayed (factory default setting).

on

The current or power of slave units is displayed.

Value

Parameter description

oFF

The LAN interface will be not used

on

The LAN interface will be used (factory default setting).

Value

Parameter description

SCPi

The SCPI language will be used (factory default setting).

LGCy

Legacy languages will be used.

Value

Parameter description

nonE

Remote control is performed using the PWX series commands made by Kikusui
(factory default setting).

5700

Remote control is performed using the N5700/N8700 commands made by Agilent
Technologies.

GEn

Remote control is performed using the Genesys series commands made by TDK-
Lambda.

PAG

Remote control is performed using the PAG series commands made by Kikusui.

dCS

Remote control is performed using the DCS series commands made by Sorensen.

«
...
48
49
50
51
52
...
»

Содержание PWX1500H




































































































































Отзывы:

Нет отзывов

Похожие инструкции для PWX1500H

Бренд: Makita Страницы: 16

Бренд: Fein Страницы: 53

Бренд: Xinpu Страницы: 12

Central Pneumatic 1/4" Stubby Air Ratchet 91002

Бренд: Central Pneumatic Страницы: 8

PSI 9000 WR 3U SLAVE

Бренд: Elektro-Automatik Страницы: 44

XTC ARGB Series

Бренд: COUGAR Страницы: 2

Бренд: Koch Страницы: 76

Бренд: Zenit Страницы: 8

Бренд: phytron Страницы: 29

Бренд: Hakko Electronics Страницы: 8

Бренд: Corsair Страницы: 42

Бренд: DekoLight Страницы: 4

Бренд: Mengual Страницы: 68

Бренд: YATO Страницы: 64

Бренд: Eaton Страницы: 11

Бренд: Hilti Страницы: 2

CORTA OS-CORP40-30

Бренд: GTV Страницы: 12

Бренд: Milwaukee Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды