Kikusui PWX1500H Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 131

background image

PWX

83

Master-Slave Parallel Operation

Parallel

/Series Operation

4

CONFIG parameters that can be set on master units

• CF00

Resets the panel settings

• CF02 Power-on

status

parameter

• CF04  Memory content display parameter
• CF05  CC control using an Vext or Rext
• CF06  CV control using an Vext or Rext
• CF07  CV/CC control range parameter
• CF09  External control parameter for turning output on and off
• CF10  External control logic parameter for turning output on and off
• CF12

Output-on startup state parameter

• CF14

Current setting limit

• CF15 Voltage setting limit

Starting master-slave parallel operation

Turning power on

1

Turn the master unit’s POWER switch on.

2

Turn the POWER switch of each slave unit on.

3

Operate the master unit normally.

Turn output on and off from the master unit.

Turning power off

1

Turn the slave unit’s POWER switch off.

2

Turn the master unit’s POWER switch off.

CAUTION

After you turn the POWER switch off, wait at least 10 seconds after the panel display turns
off before you turn the POWER switch back on. Repeatedly turning the POWER switch on
and off at short intervals can cause damage to the inrush current limiter. In turn, this will
shorten the service life of the POWER switch, internal input fuse, and other components.

«
...
81
82
83
84
85
...
»

Содержание PWX1500H




































































































































Отзывы:

Нет отзывов

Похожие инструкции для PWX1500H

Бренд: IBM Страницы: 66

Pro Attachment PAS-225

Бренд: Echo Страницы: 28

Бренд: Solaric Страницы: 16

Бренд: Kaboodle Страницы: 2

Бренд: YATO Страницы: 64

Бренд: Parkside Страницы: 38

PARKSIDE PPHSS 715

Бренд: Parkside Страницы: 10

Бренд: Ayce Страницы: 59

Бренд: Varan Страницы: 11

Бренд: New Trent Страницы: 2

Бренд: Agilent Technologies Страницы: 179

EPSITRON 787-602

Бренд: WAGO Страницы: 2

Бренд: Yokota Страницы: 8

Бренд: BAUKER Страницы: 39

Бренд: Yamato Страницы: 25

Бренд: Mussel Страницы: 25

Бренд: F.F. Group Страницы: 64

Maxi XL Magnum HydroComp

Бренд: p-light Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды