Kikusui PWX1500H Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 131

background image

20

PWX

Connecting to the Output Terminals

1

Turn the POWER switch off.

Check that there is no voltage across the output terminals.

2

Connect one end of the included chassis connection wire to the chassis
terminal, and then connect the other end of the wire to the negative or
positive output terminal.

Use the screw on the PWX to connect the wire to the chassis terminal. Use the screw
on the output terminal to connect the wire to the output terminal.

WARNING

Risk of electric shock.

• Turn the POWER switch off before you touch the OUTPUT terminals.
• Even if you turn the output off or turn the POWER switch off, if the bleeder on/off set-

ting (CF11) is set to “oFF,” the voltage that was present when the output was on will
remain at the output terminals. Set the bleeder on/off setting to “on” before you
touch the output terminals.

• Regardless of whether load cables are connected to the output terminals, be sure to

attach the OUTPUT terminal cover before turning the POWER switch on.

Chassis terminal

- (negative) terminal

+ (positive) terminal

The PWX1500ML is in this example.

Chassis
connection wire

Screw (M3)

Screw (M4)

Chassis
connection wire

Screw (M3)

Screw (M4)

Target model
PWX750LF
PWX750MLF
PWX1500L
PWX1500ML

Target model
PWX750MHF
PWX750HF
PWH1500MH
PWX1500H

«
...
18
19
20
21
22
...
»

Содержание PWX1500H




































































































































Отзывы:

Нет отзывов

Похожие инструкции для PWX1500H

COILTHREAD KFS-30

Бренд: Kato Страницы: 2

Бренд: EINHELL Страницы: 24

PSBEN 2024B/LCD

Бренд: Pulsar Страницы: 44

Бренд: Ferm Industrial Страницы: 46

Бренд: SilverStone Страницы: 12

Бренд: Senco Страницы: 32

BOMAG BPR 50/55 D

Бренд: Fayat Страницы: 112

Бренд: Hilti Страницы: 5

Бренд: Hilti Страницы: 191

Бренд: FOREDOM Страницы: 4

Бренд: Folio Страницы: 30

Бренд: Circuit-test Страницы: 10

Бренд: Integrated Power Designs Страницы: 2

Бренд: OKU Страницы: 24

Бренд: Sealey Страницы: 4

Бренд: Stanley Страницы: 96

Бренд: Omega Страницы: 2

MASTER PROBLAST 3 ESD

Бренд: Vaniman Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды