Kikusui PWX1500H, Руководство пользователя

Страница: 63 / 131

PWX
63
About the J1 Connector
External Con
trol
3
J1 connector pin arrangement
Connector type 5747461-3 (AMP)
Plug type 745211-7 (AMP)
Wire diameter AWG26 to AWG22
Manual pressure weld-
ing tool AMP handle assembly 58074-1
AMP head assembly 58063-2
Insertion/extraction tool AMP 91232-1 or equivalent
J1
1
2
3 4 5
6 7 8 9 10 11 12 13
14 15 16 17 18 19 20 21 22 23 24 25
Pin number positions when you are
facing the rear panel
Pin
no.
Signal name Description
1 STATUS COM
Status signal common for pins 2, 3, and 14 to 16.
1
2 CV STATUS
On when the PWX series is in CV mode (open-collector output from a photocoupler).
2
3 CC STATUS
On when the PWX series is in CC mode (open-collector output from a photocoupler).
2
4 N.C. Not connected.
5 ALM CLR Alarm clear terminal.
Alarms are cleared when a LOW (0 V to 0.5 V) or short-circuit is applied to this terminal.
6 SHUT DOWN Output shutdown control terminal. The output is turned off when a LOW (0 V to 0.5 V) or short-circuit is
applied to this terminal.
7 PRL IN- Negative input terminal for master-slave parallel operation.
8 PRL IN+ Positive input terminal for master-slave parallel operation.
9 PRL COMP IN Correction signal input terminal for master-slave parallel operation.
10 A COM External signal common for pins 5 to 9, 11 to 13, 20 to 22, 24, and 25.
During remote sensing, this is the negative electrode (-S) of sensing input. When remote sensing is not
being performed, this is connected to the negative output.
11 PRL OUT+ Positive electrode output terminal for master-slave parallel operation.
12 PRL COMP OUT Correction signal output terminal for master-slave parallel operation.
13 I SUM Current signal terminal for master-slave parallel operation.
14 ALM STATUS On when a protection function (OVP, OVP2, OCP, OHP, OHP2, FAN, SEN, or AC_FAIL) has been acti-
vated or when an output shutdown signal is being applied (output through an open-collector photocou-
pler).
2
15 PWR ON STATUS Outputs a low level signal when power is turned on (output through an open-collector photocoupler).
2
16 OUT ON STATUS
On when output is on (output through an open-collector photocoupler).
2
17 N.C. Not connected.
18 OUT ON/OFF
CONT Output on/off terminal.
On when set to LOW (0 V to 0.5 V) or shorted; off when set to HIGH (4.5 V or 5 V) or open (CF10: Lo)
On when set to HIGH (4.5 V to 5 V) or open; off when set to LOW (0 V or 0.5 V) or shorted (CF10: Hi)
19 A COM External signal common for pins 5 to 9, 11 to 13, 20 to 22, 24, and 25.
During remote sensing, this is the negative electrode (-S) of sensing input. When remote sensing is not
being performed, this is connected to the negative output.
20 REF OUT External resistance control terminal; 5.25 V (CF07: Lo) or 10.5 V (CF07: Hi). The maximum output current
2.5 mA.
21 I PGM Terminal used to control the output current with an external voltage or external resistance.
0 V to 5 V; 0 % to 100 % of the rated output current (CF07: Lo).
0 V to 10 V; 0 % to 100 % of the rated output current (CF07: Hi).
22 V PGM Terminal used to control the output voltage with an external voltage or external resistance.
0 V to 5 V; 0 % to 100 % of the rated output voltage (CF07: Lo).
0 V to 10 V; 0 % to 100 % of the rated output voltage (CF07: Hi).
23 A COM External signal common for pins 5 to 9, 11 to 13, 20 to 22, 24, and 25.
During remote sensing, this is the negative electrode (-S) of sensing input. When remote sensing is not
being performed, this is connected to the negative output.
24 I MON Output current monitor.
0 % to 100 % of the rated output current is generated as a voltage between 0 V and 5 V (CF08: Lo) or a
voltage between 0 V and 10 V (CF08: Hi).
25 V MON Output voltage monitor.
0 % to 100 % of the rated output voltage is generated as a voltage between 0 V and 5 V (CF08: Lo) or a
voltage between 0 V and 10 V (CF08: Hi).
1 The status common is floating (isolation voltage of 60 V or less), it is isolated from the control circuit. If connected for master-slave
parallel operation, STATUS COM of the master unit will be connected to A COM of the slave unit (it will no longer be floating).
2 Open collector output:Maximum voltage of 30 V and maximum current of 8 mA.