Kikusui PWX1500H Скачать руководство пользователя страница 109

Страница: 109 / 131

PWX

109

PWX1500L/ PWX1500ML/ PWX1500MH/ PWX1500H

cificati

ons

Interface

Common

Common
specifications

Software protocol

IEEE Std 488.2-1992

Command language

Complies with SCPI Specification 1999.0
Has a compatibility mode (switchable)

• Genesys series made by TDK-Lambda
• N5700 and N8700 made by Agilent Technologies
• DSC series made by Sorensen
• PAG series made by Kikusui

This setting does not guarantee compatibility with all measuring instrument application software and drivers.

RS232C

Hardware

Complies with the EIA232D specifications (excluding the connector)

RJ-45 connector

The RD-8P/ 9P adapter cable is an option.

Baud rate: 1200, 2400, 4800, 9600, 19200, 38400, 57600, and
115200 bps

Data length: 8 bits, Stop bits: 1 bit, Parity bit: None

No flow control

Program message terminator

LF during reception, CR/LF during transmission

USB

Hardware

Complies with the USB 2.0 specifications.
Baud rate: 480 Mbps (High speed).

Socket B type

Program message terminator

LF or EOM during reception, LF + EOM during transmission

Device class

Complies with the USBTMC-USB488 device class specifications

LAN

Hardware

IEEE 802.3 100Base-TX or 10Base-T Ethernet
Complies with LXI Specification version 1.3 Class C

IPv4, RJ-45 connector

Category 5; use a straight cable.

Communication protocol

VXI-11, HiSLIP, or SCPI-RAW

Program message terminator

VXI-11 and HiSLIP: LF or END during reception, LF + END during
transmission
SCPI-RAW: LF during reception, LF during transmission

Содержание PWX1500H




































































































































Результаты поиска

Содержание PWX1500H

Отзывы:

Похожие инструкции для PWX1500H

Бренды по названию

Популярные бренды

Kikusui PWX1500H, Руководство пользователя

Результаты поиска

Содержание PWX1500H

Отзывы:

Похожие инструкции для PWX1500H

Бренды по названию

Популярные бренды