4
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Tools Required
•
Phillips Screwdriver
•
Level
Starter Worksurface
Note:
The starter worksurface
is assembled upside down,
and when turned upright after
full-assembly, it will be the
right-hand most worksurface
as the user sits at it.
1. Begin assembly by installing
two shared-leg brackets to a
transitional leg set (leg with
shorter foot). Use three
#10 x ½” screws per bracket to
secure (Figure 1).
2. To avoid scratching top,
carefully lay worksurface
upside down on a soft,
protective surface. Install
the transitional leg set
to the underside of the
worksurface at pre-drilled
holes using four #12 x 1”
screws. The transitional leg
will be “shared” so should
be installed to the mounting
holes closest to the edge of
the worksurface such that the
center line of the leg is directly
over the end of the table
(Figure 1).
3. Install the standard leg set to
the underside of the table at
the illustrated location, in the
set of three mounting holes
using three #12 x 1
3
/
4
” screws
(Figure 1).
Note:
Starter/finisher modesty
panels are longer than
standard WorkZone modesty
panels, and are shorter than
adder modesty panels.
4. Set a starter/finisher modesty
panel between the two installed
legs over mounting holes in
worksurface as illustrated. If
optional horizontal wireway
is to be installed to unit,
place the wireway between
mounting flange of modesty
panel and the worksurface,
aligning the mounting holes
as illustrated. Secure modesty
panel to worksurface with three
#12 x 1” screws, and attach
modesty panel ends to the legs
using two #10 x ½” screws at
each leg (Figure 1).
WorkZone
®
Starter/Adder/Finisher Worksurface
Assembly Instructions
Tools Required
Phillips Screwdriver
Level
Starter Worksurface
Note:
Note:
The starter worksurface is assembled
upside down, and when turned upright after
full-assembly, it will be the right-hand most
worksurface as the user sits at it.
1. Begin assembly by installing two shared-
leg brackets to a transitional leg set (leg with
shorter foot). Use three #10 x ½” screws per
bracket to secure (Figure 1).
2. To avoid scratching top, carefully lay
worksurface upside down on a soft,
protective surface. Install the transitional leg
set to the underside of the worksurface at
pre-drilled holes using four #12 x 1” screws.
The transitional leg will be “shared” so should
be installed to the mounting holes closest to
the edge of the worksurface such that the
centerline of the leg is directly over the end of
the table (Figure 1).
3. Install the standard leg set to the underside
of the table at the illustrated location, in the
set of three mounting holes using three
#12 x 1- / ” screws (Figure 1).
Starter/finisher modesty panels are
longer than standard WorkZone modesty
panels, and are shorter than adder modesty
panels.
4. Set a starter/finisher modesty panel
between the two installed legs over mounting
holes in worksurface as illustrated. If optional
horizontal wireway is to be installed to unit,
place the wireway between mounting flange
of modesty panel and the worksurface,
aligning the mounting holes as illustrated.
Secure modesty panel to worksurface with
three #12 x 1” screws, and attach modesty
panel ends to the legs using two #10 x ½”
screws at each leg (Figure 1).
3
4
Figure 1 - Starter Worksurface
shared-leg
bracket
transitional leg set
(shorter foot)
standard
leg set
shared-leg
bracket
#10 x ½”
screws
#12 x 1”
screw
#12 x 1- / ”
screw
3
4
#12 x 1”
screw
starter/finisher
modesty panel
(shorter length)
starter
worksurface
#10 x ½”
screw
Starter/Adder/Finisher Worksurface Assembly
#12 x 1" screw
#10 x / " screw
1
2
leg plug
#12 x 1 / ” screw
3
4
horizontal
wireway
(optional)
Figure 1 - Starter Worksurface
#12 x 1
3
/
4
”
screw
