KI WorkZone Скачать руководство пользователя

Страница: 14 / 36

Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.

8. Stand worksurface assembly

right side up and install two leg

plugs into the exposed holes at

the outside of each leg set as

illustrated (Figure 3).

Note:

Two different vertical

wireway halves are supplied with

power & data tables: The “vertical

wireway - inner” (with two

cut-outs) is to be installed facing

the inside of the table (Figures 2

& 3). The “vertical wireway-outer,

with power/data” (single cut-out)

(Figures 2 & 3) is to be installed

on the outside of a leg, and the

cut-out must face the underside

of the table. Whenever a

”table-to-table wireway” is

installed (Figure 2), the vertical

wireways must be installed to the

leg set before the table-to-table

wireway is installed.

9. Vertical wireways fasten into each

other from each side of the leg

set opening and must be oriented

correctly to press together.

Begin by first positioning an

“outer vertical wireway” (single

cut-out), to the outside of the leg

set as illustrated, with cut-out

closest to worksurface. Next

position the inner wireway cover

(two cut-outs) in the correct

orientation at the inside of the

leg set and press it into the outer

wireway (Figures 2 & 3). For

end-of run tables, press a vertical

wireway cap into the upper,

outside cut-out in each vertical

wireway where no table-to-table

wireway is installed (Figure 3).

10. If worksurface assemblies are to

be ganged, attach them together

with #12 x 1” screws at table-to-

table wireway and splice plate.

Do not tighten at this time.

11. Level worksurface by turning

four adjustable glides either in

or out. The jambnuts between

the glides and the bottom of

the leg sets must be tightened

up against the bottom of the leg

to secure the adjustable glides

(Figure 3). Tighten screws that

gang worksurfaces at this time.

12. Press worksurface grommets into

wireway holes in worksurface top

(Figure 3). Route the power and

data module cord through the

power and data module hole in

the worksurface. Snap the power

and data module into the module

hole (Figure 3). From under the

worksurface, with the power/data

door opened, plug the power cord

into the duplex receptacle on the

10-wire harness. Check for proper

operation of the power and data

module. To open module push

down on the module and it will

pop-up. To close, press downward

and it will snap closed.

WorkZone

Desks - 24”, 30” x 60”, 66” & 72” Tops with Power & Data

Assembly Instructions

4. Position the mounting bracket of the
power/data door over the modesty panel
holes that correspond with worksurface
holes. Insert three #12 x 1” screws through
the mounting bracket and modesty panel
into the worksurface. Tighten all screws to
secure the leg sets and modesty panel
(Figure 1).

5. Fasten door clips to the underside of the
worksurface with two #12 x 1” screws per
door clip (Figure 1).

6. If worksurfaces will be ganged together,
attach table-to-table wireway to underside of
worksurface with two #12 x 1” screws on
ganging end(s). Also, attach splice plate to
worksurface with two #12 x 1” screws at
same end(s) (Figure 1).

All 10-wire harnesses must be

oriented the same direction to make proper
connections. At one end of each harness, on
the black connector near the clip, is an (N)
and arrow under the worksurface at the left
side, with the arrow pointing to the modesty
panel.

7. Correctly orient the two 10-wire
harnesses to the underside of the
worksurface with the arrows pointing to the
modesty panel as noted above (Figure 1).
Position the 10-wire harnesses

Plug duplex receptacle into power harness
as illustrated. Secure receptacle to power
harness by sliding into port until spring clips
lock receptacle into place (Figure 1)

Note:

Whenever tables are to be joined with

a table-to-table wireway and splice plate
(Figures 1 & 2 ), the inner and outer vertical
wireway sections must be installed into the
leg prior to installing the table-to-table
wireway to the worksurface. Refer now to
the “Note” and step 9 if this is the case.
Then return back to step 6 below.

to underside

of worksurface over pre-drilled mounting
holes and attach with four #12 x 1” screws

Note:

If the position of the table requires that

the floor infeed be wired up at the end of a
run of worksurfaces, the vertical wireway
will be replaced by a floor feed vertical
wireway which is explained in instructions
14 through 17.

8. Stand worksurface assembly right side up
and install two leg plugs into the exposed
holes at the outside of each leg set as
illustrated (Figure 3).

Note:

Two different vertical wireway halves

are supplied with power & data tables: The
“vertical wireway - inner” (with two cut-
outs) is to be installed facing the inside of
the table (Figures 2 & 3). The “vertical
wireway-outer, with power/data” (single cut-
out) (Figures 2 & 3) is to be installed on the
outside of a leg, and the cut-out must face
the underside of the table. Whenever a
”table-to-table wireway” is installed (Figure
2), the vertical wireways must be installed to
the leg set before the table-to-table wireway
is installed.

9. Vertical wireways fasten into each other
from each side of the leg set opening and
must be oriented correctly to press together.
Begin by first positioning an “outer vertical
wireway” (single cut-out), to the outside of
the leg set as illustrated, with cut-out closest
to worksurface. Next position the inner
wireway cover (two cut-outs) in the correct
orientation at the inside of the leg set and
press it into the outer wireway (Figures 2 &
3). For end-of run tables, press a vertical
wireway cap into the upper, outside cut-out
in each vertical wireway where no table-to-
table wireway is installed (Figure 3).

WorkZone with Power & Data - Assembly Instructions

vertical wireway-outer

with power/data

(single cut-out)

transitional

leg

splice

plate

vertical wireway-inner

(two cut-outs)

Figure 2

table-to-table