KI WorkZone Скачать руководство пользователя | Manualshive

Страница: 8 / 36

background image

8

Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.

17. Install a vertical wireway into

each leg set by first positioning

the outer wireway section as

illustrated. The extended face of

the wireway must be oriented up

so as to cover the table-support

member of the leg set when

installed. Incorrectly installed, it

will cover the foot member. Flex

the outer wireway slightly and

press it into place between the

leg uprights. Next position the

inner wireway cover as illustrated

and press it into place in the

vertical wireway (Figure 6).

18. Press worksurface grommets into

wireway holes in worksurface

top, and install two leg plugs

into the two exposed holes at

the outside of each leg set as

illustrated (Figure 6).

WorkZone

®

Starter/Adder/Finisher Worksurface

Assembly Instructions

15. Install a vertical wireway into each leg
set by first positioning the outer wireway
section as illustrated. The extended face
of the wireway must be oriented up so as
to cover the table-support member of the
leg set when installed. Incorrectly
installed, it will cover the foot member.
Flex the outer wireway slightly and press
it into place between the leg uprights.
Next position the inner wireway cover as
illustrated and press it into place in the
vertical wireway (Figure 3).

16. Press worksurface grommet cover
into wireway holes in worksurface top,
and install two leg plugs into the two
exposed holes at the outside of each leg
set as illustrated (Figure 6).

Starter/Adder/Finisher Worksurface Assembly

leg plug

vertical

wireway - outer

vertical

wireway - inner

leg set

adjustable

glide

Figure 6 - Vertical Wireways

worksurface

grommet cover

Figure 6 - Vertical Wireways

«
...
6
7
8
9
10
...
»

Содержание WorkZone





































Отзывы:

Нет отзывов

Похожие инструкции для WorkZone

Бренд: GALA MEBLE Страницы: 15

Бренд: J&K Страницы: 7

Бренд: Samsung Страницы: 92

Бренд: X-METAL Страницы: 18

KENDARA MEDIA CREDENZA BH18-021-199-14

Бренд: Better Homes and Gardens Страницы: 32

Бренд: Inova Страницы: 57

Бренд: Twin-Star International Страницы: 13

Бренд: Venjakob Страницы: 2

Бренд: Zenith Страницы: 10

Бренд: SAFAVIEH COUTURE Страницы: 22

RUNDBANK RONCADE 1 & 2

Бренд: hanit Страницы: 3

Бренд: HULALA HOME Страницы: 9

Бренд: Multimo Страницы: 14

Paulette Hutch SK014

Бренд: Ballard Designs Страницы: 4

Бренд: Amart Furniture Страницы: 10

Бренд: Office Star Products Страницы: 2

Бренд: PATIOJOY Страницы: 7

Бренд: Habitat Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды