10
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
WorkZone
®
Desks - 24”, 30” x 30” through 54” Tops with Power & Data
Assembly Instructions
Note:
If the position of the table
requires that the floor infeed
be wired up at the end of a run
of worksurfaces, the vertical
wireway will be replaced by a
floor feed vertical wireway which
is explained in instructions 14
through 17.
8. Stand worksurface assembly
right side up and install two leg
plugs into the exposed holes at
the outside of each leg set as
illustrated (Figure 3).
Note:
Two different vertical
wireway halves are supplied
with power & data tables: The
“vertical wireway - inner” (with
two cut-outs) is to be installed
facing the inside of the table
(Figures 2 & 3). The “vertical
wireway-outer, with power/data”
(single cut-out) (Figures 2 & 3) is
to be installed on the outside of a
leg, and the cut-out must face the
underside of the table. Whenever
a ”table-to-table wireway” is
installed between tables (Figure
2), the vertical wireways must
be installed to the leg set before
the table-to-table wireway is
installed.
9. Vertical wireways fasten into each
other from each side of the leg
set opening and must be oriented
correctly to press together.
Begin by positioning an “outer
vertical wireway” (one cut-out),
to the outside of the leg set as
illustrated with the cut-out facing
the worksurface. Next position
the inner wireway cover (two cut-
outs) in the correct orientation at
the inside of the leg set and press
it into the outer. Press a vertical
wireway cap into the upper,
outside cut-out in each vertical
wireway where no table-to-table
wireway is installed (Figure 3).
10. If worksurface assemblies are to
be ganged, attach them together
with #12 x 1” screws at table-to-
table wireway and splice plate.
Do not tighten at this time.
4. Position the mounting bracket of the
power/data door over the modesty panel
holes that correspond with worksurface
holes. Insert three #12 x 1” screws through
the mounting bracket and modesty panel
into the worksurface. Tighten all screws to
secure the leg sets and modesty panel
(Figure 1).
5. Fasten door clips to the underside of the
worksurface with two #12 x 1” screws per
door clip (Figure 1).
Whenever tables are to be joined with
a table-to-table wireway and splice plate
(Figure 1), the vertical wire way (Figures 2 &
3) must be installed into the leg prior to the
table-to-table wireway being installed to the
worksurface. Refer now to step 9 and the
note before, if this is the case. Then return
back to step 6 below.
6. If worksurfaces will be ganged together,
attach table-to-table wireway to underside of
worksurface with two #12 x 1” screws on
ganging end(s). Also, attach splice plate to
worksurface with two #12 x 1” screws at
same end(s) (Figure 1).
All 10-wire harnesses must be
oriented the same direction to make proper
connections. At one end of each harness, on
the black connector near the clip, is an (N)
and arrow under the worksurface at the left
side, with the arrow pointing to the modesty
panel.
7. Correctly orient the 10-wire harness to the
underside of the worksurface with the arrow
pointing to the modesty panel as noted
above (Figure 1). Position 10-wire harness
to underside of worksurface over pre-drilled
mounting holes and attach with four #12 x
1” screws. Plug duplex receptacle into
power harness as illustrated. Secure
receptacle to power harness by sliding into
port until spring clips lock receptacle into
place (Figure 1).
Note:
Note:
Note:
If the position of the table requires
that the floor infeed be wired up at the
end of a run of worksurfaces, the
vertical wireway will be replaced by a
floor feed vertical wireway which is
explained in instructions 14 through 17.
8. Stand worksurface assembly right
side up and install two leg plugs into the
exposed holes at the outside of each leg
set as illustrated (Figure 3).
9.
a vertical wireway cap into the upper,
outside cut-out in each vertical wireway
where no table-to-table wireway is
installed (Figure 3).
Note:
Two different vertical wireway
halves are supplied with power & data
tables: The “vertical wireway - inner”
(with two cut-outs) is to be installed
facing the inside of the table (Figures 2
& 3). The “vertical wireway-outer, with
power/data” (single cut-out) (Figures 2
& 3) is to be installed on the outside of a
leg, and the cut-out must face the
underside of the table. Whenever a
”table-to-table wireway” is installed
between tables (Figure 2), the vertical
wireways must be installed to the leg set
before the table-to-table wireway is
installed.
Vertical wireways fasten into each
other from each side of the leg set
opening and must be oriented correctly
to press together. Begin by positioning
an “outer vertical wireway” (one cut-
out), to the outside of the leg set as
illustrated with the cut-out facing the
worksurface. Next position the inner
wireway cover (two cut-outs) in the
correct orientation at the inside of the
leg set and press it into the outer.
Press
WorkZone with Power & Data - Assembly Instructions
vertical wireway-outer
with power/data
(single cut-out)
transitional
leg
splice
plate
vertical wireway-inner
(two cut-outs)
Figure 2
table-to-table
wireway
leg plug
vertical
wireway cap
leg set
adjustable
glide
Figure 3
power & data
module
vertical
wireway-outer
(end-of-run)
vertical
wireway-inner
worksurface
grommet cover
power and
data module
Figure 3
11. Level worksurface by turning
four adjustable glides either in
or out. The jambnuts between
the adjustable glides and the
bottom of the leg sets must
be tightened up against the
bottom of the leg to secure
the adjustable glides (Figure
3). Tighten screws that gang
worksurfaces at this time.
12. Press worksurface grommets
into wireway holes in
worksurface top (Figure 3).
Route the power and data
module cord through the
power and data module hole
in the worksurface. Snap the
power and data module into
the module hole (Figure 3).
From under the worksurface,
with the power/data door
opened, plug the power cord
into the duplex receptacle on
the 10-wire harness. Check for
proper operation of the power
and data module. To open
module push down on the
module and it will pop-up. To
close, press downward and it
will snap closed.
