6
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
11. Twist in four #12 x 1” screws
through the shared-leg bracket
of the starter worksurface, and
into the pre-drilled mounting
holes at the underside of
the adder worksurface as
illustrated. Do not tighten
screws completely at this time
(Figure 4).
12. Twist in two #10 x ½” screws
through the side of the adder
modesty panel and into the leg
of the starter worksurface, but
do not tighten screws at this
time (Figure 4).
Note:
any number of
additional adder worksurfaces
can be attached to existing
adder worksurfaces following
the steps above.
WorkZone
®
Starter/Adder/Finisher Worksurface
Assembly Instructions
standard
leg set
#10 x ½”
screws
#12 x 1”
screw
#12 x
screw
starter/finisher
modesty panel
(shorter length)
finisher
worksurface
adder
worksurface
assembly
starter
worksurface
assembly
shared-leg
bracket
transitional leg set
(shorter foot)
transitional leg set
(shorter foot)
#12 x 1”
screw
#10 x ½”
screw
adder
modesty panel
(longer)
standard
leg set
horizontal
wireway
(optional)
Figure 3 - Finisher Worksurface
Figure 4 - Adder to Starter Assembly
Finisher Worksurface
Note:
The finisher worksurface
is assembled upside down,
and when turned upright after
full-assembly, it will attach to an
adder worksurface.
8. To avoid scratching top, carefully
lay finisher worksurface upside
down on a soft, protective
surface. Install a standard leg
set to the underside of the
worksurface at pre-drilled
holes using three #12 x 1
3
/
4
”
screws. The standard leg set
is “not shared” so should not
be installed to the mounting
holes closest to the edge of the
worksurface (Figure 3).
Note:
Starter/finisher modesty
panels are longer than standard
WorkZone modesty panels, and
are shorter than adder modesty
panels.
9. Position a starter/finisher
modesty panel over the
mounting holes in the
worksurface, and next to the
standard leg as illustrated. If
optional horizontal wireway is
to be installed to unit, place
the wireway between mounting
flange of modesty panel and
the worksurface, aligning the
mounting holes as illustrated.
Secure modesty panel to
worksurface with three
#12 x 1” screws, and attach
one modesty panel end to the
standard leg using two
#10 x ½” screws (Figure 3).
Starter/Adder Assembly
10. Carefullly turn the starter
worksurface assembly to the
upright position. With care,
turn the adder worksurface
assembly upright, next to the
starter unit and set the no-leg
end of the adder surface onto
the shared-leg bracket of the
starter worksurface assembly
(Figure 4).
standard
leg set
#10 x ½”
screws
#12 x 1”
screw
#12 x
screw
starter/finisher
modesty panel
(shorter length)
finisher
worksurface
adder
worksurface
assembly
starter
worksurface
assembly
shared-leg
bracket
transitional leg set
(shorter foot)
transitional leg set
(shorter foot)
#12 x 1”
screw
#10 x ½”
screw
adder
modesty panel
(longer)
standard
leg set
horizontal
wireway
(optional)
