manualshive.com logo in svg

Keysight E8663D, Руководство пользователя

Keysight E8663D - мощный и точный генератор сигналов, обеспечивающий высокую стабильность и надежность. Для удобства использования, вы можете скачать бесплатное руководство пользователя с нашего веб-сайта. Наслаждайтесь всеми функциями устройства, загрузив его руководство с manualshive.com.

Поделиться
Скачать
background image

Keysight E8357D/67D & E8663D PSG User’s Guide                                                                                                   35

Signal Generator Overview
Rear Panel

without Option 601/602, this female BNC connector can be used to output the 

complement of the quadrature–phase component of an external I/Q 

modulation that has been fed into the Q input connector.
Q–bar OUT is used in conjunction with Q OUT to provide a balanced baseband 

stimulus. Balanced signals are signals present in two separate conductors that 

are symmetrical relative to ground and are opposite in polarity (180 degrees 

out of phase). The nominal output impedance of the Q–bar OUT connector is 

50 ohms, dc–coupled.

15. AC Power Receptacle

The ac line voltage is connected here. The power cord receptacle accepts a 

three–pronged power cable that is shipped with the signal generator.

CAUTION

Always use the three-prong AC power cord supplied with this product. Failure 

to ensure adequate earth grounding by not using this cord can cause product 

damage.

This instrument has auto-ranging line voltage input; be sure the supply 

voltage is within the specified range and voltage fluctuations do not to 

exceed 10 percent of the nominal supply voltage:

E8257D: 100/120 VAC 50/60/400 Hz, 220/240, VAC 50/60 Hz, < 250 W 

typical, 450 W maximum
E8267D: 100/120 VAC 50/60/400 Hz; or 220/240 VAC 50/60 Hz, 

(automatically selected); < 400 W typical, 650 W maximum
E8663D: 100/120 VAC 50/60/400 Hz; or 220/240 VAC 50/60 Hz, 

(automatically selected); < 250 W typical, 450 W maximum

16. GPIB

This GPIB interface allows listen and talk capability with compatible IEEE 488.2 

devices.

17. 10 MHz EFC

This female BNC input connector (Options UNR/UNX only) accepts an external 

dc voltage, ranging from 

−

5 V to +5 V, for electronic frequency control (EFC) of 

the internal 10 MHz reference oscillator. This voltage inversely tunes the 

oscillator about its center frequency (approximately 

−

0.0025 ppm/V). The 

nominal input impedance is greater than 1 Mohms. When not in use, this 

connector should be shorted using the supplied shorting cap to assure a stable 

operating frequency.

Содержание E8663D







































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E8663D

Ebode IR Link Pro Manual preview
IR Link Pro
Бренд: Ebode Страницы: 8
IDK COS-100HD-B Command Reference Manual preview
COS-100HD-B
Бренд: IDK Страницы: 24
Chefman RJ28-6-SS SERIES User Manual preview
RJ28-6-SS SERIES
Бренд: Chefman Страницы: 16
Orei UHD-EXB350EAU-K User Manual preview
UHD-EXB350EAU-K
Бренд: Orei Страницы: 21
Keysight Technologies V3050A Getting Started Manual preview
V3050A
Бренд: Keysight Technologies Страницы: 41
Hamilton Beach Classic Chrome Blender User Manual preview
Classic Chrome Blender
Бренд: Hamilton Beach Страницы: 24
LEAB BPC 12-12/40 Quick Start Manual preview
BPC 12-12/40
Бренд: LEAB Страницы: 16
SOLAC BV5713 Instructions For Use Manual preview
BV5713
Бренд: SOLAC Страницы: 60
NTI ST-FOUSB4K-LC User Manual preview
ST-FOUSB4K-LC
Бренд: NTI Страницы: 5
Hamilton Beach 56200T Use & Care Manual preview
56200T
Бренд: Hamilton Beach Страницы: 20
SMART-AVI V2V-AV2H-01 Installation Manual preview
V2V-AV2H-01
Бренд: SMART-AVI Страницы: 2
VOX electronics MS-6010 Instruction Manual preview
MS-6010
Бренд: VOX electronics Страницы: 63
F'real Freal Cleaning And Sanitizing Instructions preview
Freal
Бренд: F'real Страницы: 2
Hamilton Beach 58176 User Manual preview
58176
Бренд: Hamilton Beach Страницы: 4
Bosch CM710B Installer'S Reference Manual preview
CM710B
Бренд: Bosch Страницы: 8
Bosch FPC 7034 Manual preview
FPC 7034
Бренд: Bosch Страницы: 2
Kenwood Smoothie Concert Mini SB240 Series Instructions Manual preview
Smoothie Concert Mini SB240 Series
Бренд: Kenwood Страницы: 9
Magnavox Essence HR1780 User Manual preview
Essence HR1780
Бренд: Magnavox Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды