manualshive.com logo in svg

Keysight E8663D, Руководство пользователя

Keysight E8663D - мощный и точный генератор сигналов, обеспечивающий высокую стабильность и надежность. Для удобства использования, вы можете скачать бесплатное руководство пользователя с нашего веб-сайта. Наслаждайтесь всеми функциями устройства, загрузив его руководство с manualshive.com.

Поделиться
Скачать
background image

Keysight E8357D/67D & E8663D PSG User’s Guide                                                                                                   37

Signal Generator Overview
Rear Panel

For Option UNR/UNX or instruments with serial prefixes > US4805/MY4805, 

this BNC connector accepts a signal with a nominal input level of 5 

±

5 dBm. 

The external frequency reference must be 10 MHz, within 

±

1 ppm.

The nominal input impedance is 50 ohms with a damage level of 

≥ 

10 dBm.

21. LAN

This LAN interface allows ethernet local area network communication through 

a 10Base–T LAN cable. The yellow LED on the interface illuminates when data 

transmission (transfer/receive) is present. The green LED illuminates when 

there is a delay in data transmission or no data transmission is present.

22. 10 MHz OUT

This female BNC connector outputs a nominal signal level of > 

+

4 dBm  and  has 

an output impedance of 50 ohms. The accuracy is determined by the timebase 

used.

23. STOP SWEEP IN/OUT

This female BNC connector (Option 007 only) provides an open–collector, 

TTL–compatible input/output signal that is used during ramp sweep operation. 

It provides low–level (nominally 0 V) output during sweep retrace and 

band–cross intervals. It provides high–level (nom5 V) output during the 

forward portion of the sweep. Sweep stops when this input/output connector is 

grounded externally. When operating as an input, the nominal impedance for 

this connector is less than 10 ohms. When operating as an output, the nominal 

impedance is approximately 4.2 kohms.

24. BASEBAND GEN CLK IN

This female BNC connector accepts a sine or square wave PECL clock input 

with a frequency range of 200 MHz to 400 MHz, resulting in sample rates of 

50 MSa/s to 100 MSa/s. The recommended input level is approximately 1 

Vpeak–to–peak for a square wave and 1 dBm to 6 dBm for a sine wave. This 

allows baseband generators from multiple signal sources to run off the same 

clock.

25. Z–AXIS BLANK/MKRS

This female BNC connector (Option 007 only) supplies a +5 V (nominal) level 

during retrace and band–switch intervals of a step, list, or ramp sweep. During 

ramp sweep, this female BNC connector supplies a –5 V (nominal) level when 

the RF frequency is at a marker frequency and intensity marker mode is on. 

This signal is derived from an operational amplifier output so the load 

impedance should be greater than or equal to 5 kohms. This connection is 

most commonly used to interface with an Keysight 8757D Scalar Network 

Analyzer.

Содержание E8663D







































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E8663D

Hamilton Beach 51101 - Single Serve Blender User Manual preview
51101 - Single Serve Blender
Бренд: Hamilton Beach Страницы: 20
Hamilton Beach 51101 - Single Serve Blender Manual preview
51101 - Single Serve Blender
Бренд: Hamilton Beach Страницы: 20
Hamilton Beach 51101 - Single Serve Blender Instruction Manual preview
51101 - Single Serve Blender
Бренд: Hamilton Beach Страницы: 15
Medion E85029 MD 87119 Instruction Manual preview
E85029 MD 87119
Бренд: Medion Страницы: 81
Genetec Synergis IX SY-SIX-PX8 Installation Manual preview
Synergis IX SY-SIX-PX8
Бренд: Genetec Страницы: 25
ATEN CE800 User Manual preview
CE800
Бренд: ATEN Страницы: 50
ottimo GTM-8206 Instruction Manual preview
GTM-8206
Бренд: ottimo Страницы: 17
Tripp Lite B132-004 Owner'S Manual preview
B132-004
Бренд: Tripp Lite Страницы: 7
PourXuan PX-HD10KM-SDI User Manual preview
PX-HD10KM-SDI
Бренд: PourXuan Страницы: 4
ATEN CE610A User Manual preview
CE610A
Бренд: ATEN Страницы: 29
PTN TPHD403PL User Manual preview
TPHD403PL
Бренд: PTN Страницы: 16
WILSON PRO 620037 Quick Start Manual preview
620037
Бренд: WILSON PRO Страницы: 2
Taurus Bapi 850 Inox Manual preview
Bapi 850 Inox
Бренд: Taurus Страницы: 110
Westinghouse 4895091378505 Instructions Manual preview
4895091378505
Бренд: Westinghouse Страницы: 36
Nikrans BD-500N 5G Installation Manual preview
BD-500N 5G
Бренд: Nikrans Страницы: 19
Moulinex LM125D Manual preview
LM125D
Бренд: Moulinex Страницы: 6
Well BLENDER-KEEN-WL Instruction Manual preview
BLENDER-KEEN-WL
Бренд: Well Страницы: 4
Well Aroma Instruction Manual preview
Aroma
Бренд: Well Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды