Keysight E8663D Скачать руководство пользователя страница 328

Страница: 328 / 358

314 Keysight E8357D/67D & E8663D PSG User’s Guide

Troubleshooting

RF Output Power Problems

Check the

RF ON/OFF

annunciator on the display. If it reads

RF OFF

, press

RF On/Off

to toggle the RF output on.

No RF Output Power when Playing a Waveform File (E8267D only)

Preset the signal generator, then replay the waveform file.
If a header file is not specified for a waveform, the signal generator uses a

default header file with unspecified settings. If you play a waveform file that

has unspecified signal generator settings; (settings not saved to the file

header, see

page 107

), the signal generator will use the header file settings

from the previously played file. If the previous header file had a marker routed

to RF blanking, the RF output power will be blanked. Preset the signal

generator to return the RF blanking marker function to its default state (Off)).

Refer to the

Key Reference

, Marker section, for more information.

NOTE

If the default marker file is used, ensure that the

Pulse/RF Blank

softkey is set

None

. Markers may have been set to

Pulse/RF Blank

by a previous file

header.

RF Output Power too Low

NOTE

On E8267D’s, an

–222 Data out of range

(“output power”) error can be

caused by:

— An incorrect waveform RMS voltage when using the signal generator with

the ALC off.

— The marker signal is not routed correctly to the ALC hold and the pulse

modulator for complex wireless signals.

For these instrument setups, if the signal is unleveled, the instrument does

not have sufficient power available.

Look for an

OFFS

REF

indicator in the

AMPLITUDE

area of the display.

OFFS

tells you that an amplitude offset has been set. An amplitude offset

changes the value shown in the

AMPLITUDE

area of the display but does

not affect the output power. The amplitude displayed is equal to the

current power output by the signal generator hardware plus the value for

the offset.
To eliminate the offset, press the following keys:

Amplitude

More (1 of 2)

Ampl Offset

Содержание E8663D







































































































































































































































































































































































Результаты поиска

Содержание E8663D

Отзывы:

Похожие инструкции для E8663D

Бренды по названию

Популярные бренды

Keysight E8663D, Руководство пользователя

Результаты поиска

Содержание E8663D

Отзывы:

Похожие инструкции для E8663D

Бренды по названию

Популярные бренды