Keysight E8663D Скачать руководство пользователя страница 271

Страница: 271 / 358

Keysight E8357D/67D & E8663D PSG User’s Guide 257

Multitone Waveform Generator
Creating, Viewing, and Optimizing Multitone Waveforms

To Minimize Carrier Feedthrough

This procedure describes how to minimize carrier feedthrough and measure

the difference in power between the tones and their intermodulation distortion

products. Carrier feedthrough can only be observed with even–numbered

multitone waveforms.
This procedure builds upon the previous procedure.

On the spectrum analyzer, set the resolution bandwidth for a sweep rate

of about

100 to 200 ms. This will allow you to dynamically view the carrier

feedthrough spike as you make adjustments.

On the signal generator, press

I/Q

I/Q Adjustments

Off On

to On.

Press

I Offset

and turn the rotary knob while observing the carrier

feedthrough with the spectrum analyzer. Changing the I offset in the

proper direction will reduce the feedthrough level. Adjust the level as low

as possible.

Press

Q Offset

and turn the rotary knob to further reduce the carrier

feedthrough level.

Repeat steps 3 and 4 until you have reached the lowest possible carrier

feedthrough level.

On the spectrum analyzer, return the resolution bandwidth to its previous

setting.

Turn on waveform averaging.

Create a marker and place it on the peak of one of the end tones.

Create a delta marker and place it on the peak of the adjacent

intermodulation product, which should be spaced 10 MHz from the

marked tone.

10.

Measure the power difference between the tone and its distortion

product.

You should now see a display that is similar to the one shown in

Figure 9-6

Your optimized multitone signal can now be used to measure the IMD products

generated by a device–under–test.
Note that carrier feedthrough changes with time and temperature. Therefore,

you will need to periodically readjust your I and Q offsets to keep the signal

optimized.

Содержание E8663D







































































































































































































































































































































































Результаты поиска

Содержание E8663D

Отзывы:

Похожие инструкции для E8663D

Бренды по названию

Популярные бренды

Keysight E8663D, Руководство пользователя

Результаты поиска

Содержание E8663D

Отзывы:

Похожие инструкции для E8663D

Бренды по названию

Популярные бренды