Keysight E8663D Скачать руководство пользователя страница 169

Страница: 169 / 358

Keysight E8357D/67D & E8663D PSG User’s Guide 155

Optimizing Performance
Creating and Applying User Flatness Correction

NOTE

A power meter timeout may occur at low power levels. If a power meter

timeout error message appears, increase the timeout value by pressing

Amplitude

More (1 of 2)

User Flatness > More (1 of 2) > Meter Timeout

Press

Done

Pressing the

Done

softkey loads the amplitude correction values into the

user flatness correction array.
If desired, press

Configure Cal Array

This opens the user flatness correction array, where you can view the

stored amplitude correction values. The user flatness correction array title

displays

User Flatness: (UNSTORED)

indicating that the current user

flatness correction array data has not been saved to the memory catalog.

Performing the User Flatness Correction Manually

If you are not using an Keysight E4416A/17A/18B/19B power meter, or if your

power meter does not have a GPIB interface, complete the steps in this section

and then continue with the user flatness correction tutorial.

Press

More (1 of 2)

User Flatness

Configure Cal Array

This opens the User Flatness table editor and places the cursor over the

frequency value

(1 GHz) for row 1. The RF output changes to the frequency value of the

table row containing the cursor and

1.000 000 000 00

is displayed in

the

AMPLITUDE

area of the display.

Observe and record the measured value from the power meter.

Subtract the measured value from 0 dBm.

Move the table cursor over the correction value in row 1.

Press

Edit Item

> enter the difference value from step 3 >

The signal generator adjusts the RF output amplitude based on the

correction value entered.

Repeat steps 2 through 5 until the power meter reads 0 dBm.

Use the down arrow key to place the cursor over the frequency value

for the next row. The RF output changes to the frequency value of the

table row containing the cursor, as shown in the

AMPLITUDE

area of the

display.

Repeat steps 2 through 7 for every entry in the User Flatness table.

Содержание E8663D







































































































































































































































































































































































Результаты поиска

Содержание E8663D

Отзывы:

Похожие инструкции для E8663D

Бренды по названию

Популярные бренды

Keysight E8663D, Руководство пользователя

Результаты поиска

Содержание E8663D

Отзывы:

Похожие инструкции для E8663D

Бренды по названию

Популярные бренды