Keysight E8663D Скачать руководство пользователя страница 176

Страница: 176 / 358

162 Keysight E8357D/67D & E8663D PSG User’s Guide

Optimizing Performance
Creating and Applying User Flatness Correction

NOTE

For specific frequency/amplitude ranges, see the mm–wave source module

specifications.

Configure the signal generator to interface with the power meter.

Press

Amplitude

More (1 of 2)

User Flatness

More (1 of 2)

Power Meter

E4416A

E4417A

E4418B

, or

E4419B

Press

Meter Address

> enter the power meter’s GPIB address >

Enter

For E4417A and E4419B models, press

Meter Channel A B

to select

the power meter’s active channel.

Press

Meter Timeout

to adjust the length of time before the

instrument generates a timeout error if unsuccessfully attempting to

communicate with the power meter.

Press

More (2 of 2)

Configure Cal Array

More (1 of 2)

Preset List

Confirm Preset

This opens the User Flatness table editor and resets the cal array

frequency/correction list.

Press

Configure Step Array

This opens a menu for entering the user flatness step array data.

Press

Freq Start

26.5

GHz

Press

Freq Stop

GHz

Press

# of Points

Enter

This enters the desired flatness–corrected frequencies (26.5 GHz to 40

GHz in 500 MHz intervals) into the step array.

Press

Return

Load Cal Array From Step Array

Confirm Load From Step

Data

This populates the user flatness correction array with the frequency

settings defined in the step array.

Press

Amplitude

dBm

10.

Press

RF On/Off

This activates the RF output and the

RF ON

annunciator is displayed on

the signal generator.

Содержание E8663D







































































































































































































































































































































































Результаты поиска

Содержание E8663D

Отзывы:

Похожие инструкции для E8663D

Бренды по названию

Популярные бренды

Keysight E8663D, Руководство пользователя

Результаты поиска

Содержание E8663D

Отзывы:

Похожие инструкции для E8663D

Бренды по названию

Популярные бренды