Keysight E8663D Скачать руководство пользователя страница 279

Страница: 279 / 358

Keysight E8357D/67D & E8663D PSG User’s Guide 265

Two–Tone Waveform Generator

Creating, Viewing, and Modifying Two–Tone Waveforms

Figure 10-3

To Minimize Carrier Feedthrough

This procedure describes how to minimize carrier feedthrough and measure

the difference in power between the tones and their intermodulation distortion

products. Carrier feedthrough only occurs with center–aligned two–tone

waveforms.
This procedure builds upon the previous procedure.

On the spectrum analyzer, set the resolution bandwidth for a sweep rate

of about

100 to 200 ms. This will allow you to dynamically view the carrier

feedthrough spike as you make adjustments.

On the signal generator, press

I/Q

I/Q Adjustments

Off On

to On.

Press

I Offset

and turn the rotary knob while observing the carrier

feedthrough with the spectrum analyzer. Changing the I offset in the

proper direction will reduce the feedthrough level. Adjust the level as low

as possible.

Press

Q Offset

and turn the rotary knob to further reduce the carrier

feedthrough level.

Repeat steps 3 and 4 until you have reached the lowest possible carrier

feedthrough level.

On the spectrum analyzer, return the resolution bandwidth to its previous

setting.

Carrier
Feedthrough

Intermodulation
Distortion

Two–Tone
Channels

Carrier Feedthrough
Distortion

Содержание E8663D







































































































































































































































































































































































Результаты поиска

Содержание E8663D

Отзывы:

Похожие инструкции для E8663D

Бренды по названию

Популярные бренды

Keysight E8663D, Руководство пользователя

Результаты поиска

Содержание E8663D

Отзывы:

Похожие инструкции для E8663D

Бренды по названию

Популярные бренды