Keysight E8663D Скачать руководство пользователя страница 273

Страница: 273 / 358

Keysight E8357D/67D & E8663D PSG User’s Guide 259

Multitone Waveform Generator
Creating, Viewing, and Optimizing Multitone Waveforms

Figure 9-7

CCDF Plot with Fixed Phase Set

Press

Mode Setup > Initialize Table

Press

Initialize Phase Fixed Random

to Random.

Press

Random Seed Fixed Random

to Random.

10.

Press

Done

11.

Press

Apply Multitone

12.

Press

More (1 of 2) > Waveform Statistics > Plot CCDF

You should now see a display that is similar to the one shown in

Figure

9-8

. The CCDF plot displays the peak to average characteristics of the

waveform with randomly generated phases and a random seed.
The random phase setup simulates the typically random nature of

multitone waveforms. Notice that randomly distributed phases result in a

much lower peak to average ratio than fixed phases. An increase in the

number of tones with random phases will decrease the probability of a

maximum peak power occurrence.

Peak
Power

Содержание E8663D







































































































































































































































































































































































Результаты поиска

Содержание E8663D

Отзывы:

Похожие инструкции для E8663D

Бренды по названию

Популярные бренды

Keysight E8663D, Руководство пользователя

Результаты поиска

Содержание E8663D

Отзывы:

Похожие инструкции для E8663D

Бренды по названию

Популярные бренды