Keysight E8663D Скачать руководство пользователя страница 72

Страница: 72 / 358

58 Keysight E8357D/67D & E8663D PSG User’s Guide

Basic Operation
Configuring the RF Output

Highlight the frequency item for point 8, then press

Insert Item

Pressing

Insert Item

shifts frequency values down one row, beginning at

point 8. Note that the original frequency values for both points 8 and 9

shift down one row, creating an entry for point 10 that contains only a

frequency value (the power and dwell time items do not shift down).
The frequency for point 8 is still active.

10.

Press

590

MHz

11.

Press

Insert Item

–2.5

dBm

This inserts a new power value at point 8 and shifts down the original

power values for points 8 and 9 by one row.

12.

Highlight the dwell time for point 9, then press

Insert Item

A duplicate of the highlighted dwell time is inserted for point 9, shifting

the existing value down to complete the entry for point 10.

To Configure a Single List Sweep

Press

Return

Sweep

Freq & Ampl

This turns the sweep on again. No errors should occur if all parameters for

every point have been defined in the previous editing process.

Press

Single Sweep

The signal generator will single sweep the points in your list. The

SWEEP

annunciator activates during the sweep.

Press

More (1 of 2)

Sweep Trigger

Trigger Key

This sets the sweep trigger to occur when you press the

Trigger

hardkey.

Press

More (2 of 2)

Single Sweep

This arms the sweep. The

ARMED

annunciator is activated.

Press the

Trigger

hardkey.

The signal generator will single sweep the points in your list and the

SWEEP

annunciator will be activated during the sweep.

To Configure a Continuous List Sweep

Press

Sweep Repeat Single Cont

This toggles the sweep from single to continuous. A continuous repetition of

the frequencies and amplitudes configured in the list sweep are now available

at the RF OUTPUT connector. The

SWEEP

annunciator appears on the display,

indicating that the signal generator is sweeping and progression of the sweep

is shown by a progress bar.

Содержание E8663D







































































































































































































































































































































































Результаты поиска

Содержание E8663D

Отзывы:

Похожие инструкции для E8663D

Бренды по названию

Популярные бренды

Keysight E8663D, Руководство пользователя

Результаты поиска

Содержание E8663D

Отзывы:

Похожие инструкции для E8663D

Бренды по названию

Популярные бренды