Keysight E8663D Скачать руководство пользователя страница 130

Страница: 130 / 358

116 Keysight E8357D/67D & E8663D PSG User’s Guide

Basic Digital Operation
Using Waveform Markers

NOTE

Most of the procedures in this section begin at the

Marker Utilities

softkey

menu.

Viewing Waveform Segment Markers

Markers are applied to waveform segments. Use the following steps to view the

markers set for a segment (this example uses the factory–supplied segment,

SINE_TEST_WFM

In the Marker Utilities menu (

page 115

), press

Set Markers

Highlight the desired waveform segment.

In an ARB format, there is only one file (

AUTOGEN_WAVEFORM

) and it is

already highlighted.

Press

Display Markers

Zoom in Max

. The maximum zoom in range is 28

points.

Experiment with the Zoom functions to see how they display the markers.
The display can show a maximum of 460 points; displayed waveforms with a

sample point range greater than 460 points may not show the marker

locations.

When using an ARB format other than
Dual ARB, you must turn on the format
to enable the

Set Markers

softkey.

Содержание E8663D







































































































































































































































































































































































Результаты поиска

Содержание E8663D

Отзывы:

Похожие инструкции для E8663D

Бренды по названию

Популярные бренды

Keysight E8663D, Руководство пользователя

Результаты поиска

Содержание E8663D

Отзывы:

Похожие инструкции для E8663D

Бренды по названию

Популярные бренды