Keysight E8663D Скачать руководство пользователя страница 300

Страница: 300 / 358

286 Keysight E8357D/67D & E8663D PSG User’s Guide

Peripheral Devices

N5102A Digital Signal Interface Module

Figure 12-8

Example Setup using the PSG 10 MHz Frequency Reference

Refer to the five setup diagrams in

Figure 12-3 on page 279

and connect

the frequency reference cable according to the clock source.

If an external clock source is used, connect the external clock signal to the

Ext Clock In connector on the interface module.

Select the break-out board that has the output connector suited for the

application. See the

N5102A Digital Signal Interface Module Installation

Guide

for information on breakout boards.

NOTE

If the Device Interface mating connector is used with the device under test,

refer to

Figure 12-8

for the device interface connection and connect the device to the

N5102A module. Then proceed to

“Operating the N5102A Module in Output

Mode” on page 288

“Operating the N5102A Module in Input Mode” on

page 298

Refer to

Figure 12-8

. Connect the breakout board to the N5102A module’s

Device Interface connector.

Connect the device to the break-out board. See the

N5102A Digital Signal

Interface Module Installation Guide

for information on breakout board

connectivity.

Signal generator 10 MHz Out

Freq Ref connector

Device interface connection

Device under test

Break-out board

User furnished ribbon cable(s) connect
between the device and break-out board.

Common Freq Ref cable

The clock to the device is in the ribbon
cable.

Содержание E8663D







































































































































































































































































































































































Результаты поиска

Содержание E8663D

Отзывы:

Похожие инструкции для E8663D

Бренды по названию

Популярные бренды

Keysight E8663D, Руководство пользователя

Результаты поиска

Содержание E8663D

Отзывы:

Похожие инструкции для E8663D

Бренды по названию

Популярные бренды