Keysight Technologies E4981A Скачать руководство пользователя страница 151 | Manualshive

Страница: 151 / 152

background image

Appendix D

149

Error Messages

Warning Message

D.
Er
ro

r M

e

ssa

g

e

s

Warning Message

A warning message is dispalyed in the instrument status display area in the lower-left part
of the display. Pressing any of the front panel keys or executing the :DISP:CCL command
clears the message.

This message simply appears on the display since it is not known to remote environments
such as GPIB. This message is not displayed when another error message has been already
displayed in the instrument message/warning area.

The warning messages for this instrument are as follows.

WARNING: Need corr meas

When the OPEN correction, SHORT correction or LOAD correction is ON, this is
displayed when you change the setup of the cable length or measurement frequency shift (1
MHz). In this case, the OPEN correction, SHORT correction and LOAD correction are
automatically turned OFF.

WARNING: Need load meas

This is displayed when you turn ON the LOAD correction from the front panel although
the setups of the cable length and measurement frequency shift (1 MHz) differ from those
when measuring/setting up the LOAD correction data. In this case, the LOAD correction is
turned ON, but you need to measure the LOAD correction data again for accurate
measurement.

WARNING: Need open meas

This is displayed when you turn ON the OPEN correction from the front panel although the
setups of the cable length and measurement frequency shift (1 MHz) differ from those
when measuring/setting up the OPEN correction data. In this case, the OPEN correction is
turned ON, but you need to measure the OPEN correction data again for accurate
measurement.

WARNING: Need short meas

This is displayed when you turn ON the SHORT correction from the front panel although
the setups of the cable length and measurement frequency shift (1 MHz) differ from those
when measuring/setting up the SHORT correction data. In this case, the SHORT correction
is turned ON, but you need to measure the SHORT correction data again for accurate
measurement.

WARNING: Out of limit

This is displayed if the correction data is out of the valid range when measuring the
correction data. The valid range for each type of correction is as follows.

In the above table, Y is the measured admittance value, Z is the measured impedance
value, and Zref is the LOAD correction standard definition value.

Type of correction

Valid range

OPEN correction

|Y| < 20

μ

S

SHORT correction

|Z| < 20

Ω

LOAD correction

|Zref|

∞

0.9 < |Z| < |Zref|

∞

1.1

«
...
149
150
151
152
»

Содержание E4981A

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для E4981A

Бренд: Candela Страницы: 4

Бренд: Danfoss Страницы: 6

Бренд: E+E Elektronik Страницы: 40

Бренд: Kane Страницы: 16

Бренд: Kane Страницы: 60

Clavinova CLP-311

Бренд: Yamaha Страницы: 29

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 15

Бренд: Yamaha Страницы: 3

Alto Horn, Baritone, Euphonium

Бренд: Yamaha Страницы: 22

Clavinova CLP-320

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 20

Бренд: Hanna Instruments Страницы: 2

Бренд: IFM Страницы: 38

Бренд: Kingfisher Страницы: 52

EUROGRAND EG2080

Бренд: Behringer Страницы: 34

Бренд: Vector Страницы: 8

D48-F, D4B-2F, D4B-3F, D4B-7F, D48-SF

Бренд: Westinghouse Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды