Keysight Technologies E4981A Скачать руководство пользователя страница 52

Страница: 52 / 152

Chapter 4

Troubleshooting

Troubleshooting Using Service Function

NOTE

The system information of E4981A may be used for the purposes of support and repair by
Keysight Technologies, but will never be used for any other purposes.

Figure 4-5

SERVICE Page

Monitor Information

The SERVICE page displays the following monitor information, which cannot be edited on
the SERVICE page.

Saving the System Information into External Memory

The system information of E4981A can be saved into external memory.

The system information may be used for the purposes of support and repair by Keysight
Technologies.

㪼㪋㪐㪏㪈㪸㫊㪼㪈㪇㪇㪏

Table 4-2

Monitor
Information

Description

POWER ON

Displays how many times E4981A have been started up and its
cumulative power-on time.

SYSCAL
REV

Displays the program revision of the adjustment for the E4981A.

SYSCAL
DATE

Displays the date of the last adjustment for the E4981A.

Содержание E4981A

























































































































































Результаты поиска

Содержание E4981A

Отзывы:

Похожие инструкции для E4981A

Бренды по названию

Популярные бренды

Keysight Technologies E4981A, Руководство по обслуживанию

Результаты поиска

Содержание E4981A

Отзывы:

Похожие инструкции для E4981A

Бренды по названию

Популярные бренды