Keysight Technologies E4981A Скачать руководство пользователя | Manualshive

Страница: 72 / 152

background image

70

Chapter 5

Replaceable Parts

Ordering Information

Ordering Information

To order a part in the replaceable parts lists, quote the Keysight Technologies part number,
indicate the quantity required, and address the order to the nearest Keysight Technologies
Sales Office.

To order a part not listed in the replaceable parts lists, include the instrument model
number, the description and function of the part, and the quantity of parts required. Address
the order to the nearest Keysight Technologies Sales Office.

Direct Mail Order System

Within the USA, Keysight Technologies can supply parts through a direct mail order
system. There are several advantages to this system:

•

Direct ordering and shipping from the Keysight Technologies parts center in California,
USA.

•

No maximum or minimum on any mail order. (There is a minimum amount for parts
ordered through a local Keysight Technologies Sales Office when the orders require
billing and invoicing.)

•

Prepaid transportation. (There is a small handling charge for each order.)

•

No invoices.

In order for Keysight Technologies to provide these advantages, please send a check or
money order with each order.

Mail order forms and specific ordering information are available through your local
Keysight Technologies Sales Office. Addresses and telephone numbers are located in a
separate document shipped with the manuals.

Exchange Assemblies

Under the rebuilt-exchange assembly program, certain factory-repaired and tested
assemblies are available on a trade-in basis. These assemblies are offered al lower cost than
a new assembly, but meet all factory specifications required of a new assembly.

The defective assembly must be returned for credit under the terms of the rebuilt-exchange
assembly program. Any spare assembly stock desired should be ordered using the new
assembly part number.

«
...
70
71
72
73
74
...
»

Содержание E4981A

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для E4981A

Acuvim-L Series

Бренд: AccuEnergy Страницы: 83

Бренд: LaserLine Страницы: 24

Бренд: UEi Страницы: 8

Бренд: Parkside Страницы: 120

Бренд: Dräger Страницы: 538

Бренд: Bühler technologies Страницы: 33

Photo Research PR-810

Бренд: Jadak Страницы: 120

Бренд: Hanna Instruments Страницы: 2

Smart Photometer System iDip 570

Бренд: eXact Страницы: 16

BlueForce Smart

Бренд: CAME Страницы: 24

Бренд: AquaMetrix Страницы: 37

Tintometer XD 7500

Бренд: Lovibond Страницы: 164

Бренд: M-system Страницы: 5

Бренд: P3 International Страницы: 12

THERMASGARD RGTM1 Series

Бренд: S+S Regeltechnik Страницы: 16

Бренд: Grundig Страницы: 24

Бренд: Liquivision Страницы: 84

ARCTIC SUN Simply Advanced 5000

Бренд: Medivance Страницы: 274

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды