Keysight Technologies E4981A Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 152

background image

5

Certification

Keysight Technologies certifies that this product met its published specifications at the
time of shipment from the factory. Keysight Technologies further certifies that its
calibration measurements are traceable to the United States National Institute of Standards
and Technology, to the extent allowed by the Institution’s calibration facility, or to the
calibration facilities of other International Standards Organization members.

Documentation Warranty

The material contained in this document is provided "as is," and is subject to being
changed, without notice, in future editions. Further, to the maximum extent permitted by
applicable law, Keysight disclaims all warranties, either express or implied with regard to
this manual and any information contained herein, including but not limited to the implied
warranties of merchantability and fitness for a particular purpose. Keysight shall not be
liable for errors or for incidental or consequential damages in connection with the
furnishing, use, or performance of this document or any information contained herein.
Should Keysight and the user have a separate written agreement with warranty terms
covering the material in this document that conflict with these terms, the warranty terms in
the separate agreement will control.

Exclusive Remedies

The remedies provided herein are buyer’s sole and exclusive remedies. Keysight
Technologies shall not be liable for any direct, indirect, special, incidental, or
consequential damages, whether based on contract, tort, or any other legal theory.

Assistance

Product maintenance agreements and other customer assistance agreements are available
for Keysight Technologies products.

For any assistance, contact your nearest Keysight Technologies Sales and Service Office.
Addresses are provided at the back of this manual.

«
...
5
6
7
8
9
...
»

Содержание E4981A

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для E4981A

Бренд: Bacharach Страницы: 87

Бренд: ICT Страницы: 48

Бренд: OfiTE Страницы: 67

Бренд: Bacharach Страницы: 28

Бренд: RayTek Страницы: 72

Бренд: Magnetrol Страницы: 40

Бренд: Kawai Страницы: 19

Бренд: Calculated Industries Страницы: 64

Бренд: Campbell Страницы: 362

Бренд: Campbell Страницы: 60

Бренд: Campbell Страницы: 116

Бренд: Campbell Страницы: 30

Бренд: Campbell Страницы: 55

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 4

Бренд: Hanna Instruments Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды