Keysight Technologies E4981A Скачать руководство пользователя | Manualshive

Страница: 6 / 152

background image

4

safety features are maintained in operational condition.

•

Dangerous Procedure Warnings

Warnings, such as the example below, precede potentially dangerous procedures
throughout this manual. Instructions contained in the warnings must be followed.

WARNING

Dangerous voltage levels, capable of causing death, are present in this instrument.
Use extreme caution when handling, testing, and adjusting this instrument.

•

Do not connect the measuring terminals to mains.

Safety Symbols

General definitions of safety symbols used on the instrument or in manuals are listed
below.

Instruction Manual symbol: the product is marked with this symbol when it is necessary for
the user to refer to the instrument manual.

Alternating current.

Direct current.

On (Supply).

Off (Supply).

In position of push-button switch.

Out position of push-button switch.

Frame (or chassis) terminal. A connection to the frame (chassis) of the equipment which
normally include all exposed metal structure.

Stand-by.

WARNING

This warning sign denotes a hazard. It calls attention to a procedure, practice,
condition or the like, which, if not correctly performed or adhered to, could result in
injury or death to personnel.

CAUTION

This Caution sign denotes a hazard. It calls attention to a procedure, practice, condition or
the like, which, if not correctly performed or adhered to, could result in damage to or
destruction of part or all of the product.

NOTE

Note denotes important information. It calls attention to a procedure, practice, condition or
the like, which is essential to highlight.

«
...
4
5
6
7
8
...
»

Содержание E4981A

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для E4981A

Бренд: HANYOUNG NUX Страницы: 4

Бренд: jenway Страницы: 30

Бренд: National Meter & Automation Страницы: 24

Бренд: Lakeshore Страницы: 2

Бренд: Kamstrup Страницы: 4

Бренд: E-line Страницы: 164

BML SL1-ALZ-ZZ Series

Бренд: Balluff Страницы: 26

Бренд: R&S Страницы: 733

Бренд: R&S Страницы: 369

Бренд: Yamaha Страницы: 72

Бренд: Yamaha Страницы: 5

Бренд: Yamaha Страницы: 16

Бренд: Yamaha Страницы: 8

Бренд: Yamaha Страницы: 7

Бренд: Yamaha Страницы: 60

GranTouch Digital Grand Piano

Бренд: Yamaha Страницы: 19

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды