Keysight Technologies E4981A Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 152

background image

46

Chapter 4

Troubleshooting

Power On Sequence Troubleshooting

Check booting process

If the power on sequence has a problem despite it being powered from the power supply
unit properly, check the following events in this order.

1. With the E4981A plugged in and the power turned off, the orange standby LED should

be on. If the orange LED doesn’t light, check the key flex circuit, display interface
board, A31 board, and relevant cables.

2. When the front panel power switch is turned on, the orange LED should go out and the

yellow-green LED should come on. If the yellow-green LED doesn’t light, check the
key flex circuit, display interface board, A31 board, and relevant cables.

3. Three LEDs (+3.3V, +5V, and PWR_GD) on the A31 board should be on. If the LEDs

don’t light, a problem in the A31 board is suspected.

4. The fan should be rotating and audible. If the fan doesn’t run, it is probably defective.

5. The LED on the display interface board should blink. If the LED doesn’t blink, check

the display interface board, the A31 board, and the relevant cable.

6. The firmware revision and hardware option information along with copyright

declaration should be displayed. If nothing is displayed, check the LCD, display
interface board, inverter board, and the relevant cables.

7. The power on test should be executed once automatically before the measurement

starts. If the power on test fails, an error code or an error message is displayed. For
more details, refer to “Troubleshooting using service function”.

8. The measurement view should be displayed.

9. If the following error message

A31 EEPROM write error

is displayed during the

measurement process, a problem in the A31 board is suspected.

10. If the following error message

CPU Bd EEPROM write error

, or

CPU Bd FLASH

ROM write error

is displayed during the measurement process, a problem in the

PPMC PCA is suspected.

11. If the following error message

Fan failed

is displayed during the measurement process,

a problem in the fan is suspected.

12. If the following error message

Power failed

is displayed during the measurement

process, a problem in the power supply is suspected.

«
...
46
47
48
49
50
...
»

Содержание E4981A

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для E4981A

Бренд: M-system Страницы: 16

Бренд: M-system Страницы: 25

HF Scientific AccUView LED Ex

Бренд: Watts Страницы: 2

Бренд: QEED Страницы: 6

Бренд: Parkside Страницы: 120

Бренд: Ramsey Electronics Страницы: 40

Бренд: PASI Страницы: 59

Бренд: Lutron Electronics Страницы: 10

Бренд: Velleman Страницы: 38

Бренд: Rebel Страницы: 28

Бренд: TAC Страницы: 28

Бренд: X-Rite Страницы: 130

Бренд: JensPrima Страницы: 20

SoundExpert LxT

Бренд: Larson Davis Страницы: 307

Бренд: Endress+Hauser Страницы: 24

Бренд: OHAUS Страницы: 64

Бренд: Würth Страницы: 28

Бренд: Banner Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды