Keysight Technologies E4981A Скачать руководство пользователя | Manualshive

Страница: 146 / 152

background image

144

Appendix D

Error Messages

Error Messages

F

1070

Fan failed

Cooling fan hardware failure is detected.

Contact Keysight Technology’s Sales and Service Office or the company from which you
purchased the device.

G

-105

GET not allowed

A group execution trigger (GET) has been received in a program message. (Refer to
IEEE488.2,7.7.)

H

-114

Header suffix out of range

The header suffix is out of range.

I

-101

Invalid character

Invalid characters have been found in the program message string. For example, in a
correct program message “

:CALC1:FORM CP

”, an ampersand (&) is inserted by mistake

to give “

:CALC1:FORM&CP

”.

-103

Invalid separator

The parser (syntax analysis program) expects a separator, but a character other than a
separator has been sent. For example, although the correct way is to use “;” to separate two
sent program messages such as “

:CALC1:FORM CP;*OPC?

”, the semicolon (;) needed to

separate the program messages is missing to give “

:CALC1:FORM CP *OPC?

”.

-121

Invalid character in number

An invalid character for the data type of the syntax analysis target has been received. For
example, alphabetical characters exist in a decimal value or “9” exists in octal data.

-131

Invalid suffix

The suffix does not meet the syntax defined in IEEE488.2,7.7.3.2 or is inappropriate for
the E4981A.

-141

Invalid character data

A character data element has been recieved where the E4981A does not accepts any
character data element.

-151

Invalid string data

Character string data are expected, but the string data received are invalid for some reason.
(Refer to IEEE488.2,7.7.5.2.) For example, the END message is received before the end
quotation mark character appears.

«
...
144
145
146
147
148
...
»

Содержание E4981A

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для E4981A

Masoneilan 12400 Series

Бренд: Baker Hughes Страницы: 81

Бренд: Yamaha Страницы: 8

Бренд: F.W. Bell Страницы: 75

Бренд: Bamo Страницы: 8

Бренд: OHAUS Страницы: 84

Бренд: Pasco Scientific Страницы: 11

Бренд: X-laser Страницы: 17

Бренд: JRC Страницы: 308

Бренд: PITSID Страницы: 22

Бренд: Swan Analytical Instruments Страницы: 102

Microlog GX Series

Бренд: SKF Страницы: 342

Бренд: KALATEL Страницы: 38

Бренд: S+S Regeltechnik Страницы: 32

Бренд: SIGLENT Страницы: 32

DigiFlow 6710M-22

Бренд: Savant Страницы: 3

Intelligizer Fence Monitor

Бренд: Zareba Страницы: 8

WTW SensoLyt 900

Бренд: Xylem Страницы: 12

Бренд: Allen Organ Company Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды