Keysight Technologies E4981A Скачать руководство пользователя

Страница: 125 / 152

Chapter 6

123

Replacement Procedure

LCD and Display Interface Board Replacement

6. Re

placem

ent Pro

LCD and Display Interface Board Replacement

Tools Required

•

Torque screwdriver, TORX T6

•

Torque screwdriver, TORX T20

•

Box torque wrench, 5/8 inch

Removal Procedure

Refer to

Figure 6-22

and for this procedure.

Step 1.

Remove the 3/4 rack module top as described in

“3/4 Rack Module Top Replacement” on

page 92

Step 2.

Remove the PSU Deck Assembly as described in

“PSU Deck Assembly Removale” on

page 95

Step 3.

Remove the Front Panel Assembly as described in

“Front Panel Assembly Removal” on

page 101

Step 4.

Remove the Inverterl Assembly as described in

“Inverter Assembly Replacement” on

page 119

Step 5.

Remove the Display Support as described in

“Display Support Removal” on page 121

Step 6.

Remove the four TORX T6 screws (item 1) fastening the LCD.

Step 7.

Remove the LCD from the Display Support with the Display Interface Board.

Step 8.

Carefully remove the Display Interface Board from the Display Support.

Replacement Procedure

Step 1.

Reverse the order of the removal procedure.

NOTE

When you replace the LCD with a new one, stick new gaskets (P/N : E4980-25003

∞

E4980-25004

∞

2) to surroundings on the LCD Display.

Содержание E4981A

























































































































































Результаты поиска

Содержание E4981A

Отзывы:

Похожие инструкции для E4981A

Бренды по названию

Популярные бренды

Keysight Technologies E4981A, Руководство по обслуживанию

Результаты поиска

Содержание E4981A

Отзывы:

Похожие инструкции для E4981A

Бренды по названию

Популярные бренды