Keysight Technologies E4981A Скачать руководство пользователя

Страница: 123 / 152

Chapter 6

121

Replacement Procedure

Display Support Removal

6. Re

placem

ent Pro

Display Support Removal

Tools Required

•

Torque screwdriver, TORX T6

•

Torque screwdriver, TORX T20

•

Box torque wrench, 5/8 inch

Removal Procedure

Refer to

Figure 6-21

and for this procedure.

Step 1.

Remove the 3/4 rack module top as described in

“3/4 Rack Module Top Replacement” on

page 92

Step 2.

Remove the PSU Deck Assembly as described in

“PSU Deck Assembly Removale” on

page 95

Step 3.

Remove the Front Panel Assembly as described in

“Front Panel Assembly Removal” on

page 101

Step 4.

Remove the Inverter Assembly as described in

“Inverter Assembly Replacement” on

page 119

Step 5.

Disconnect the Display Cable (item 1) from the Display Interface Board Assembly.

Step 6.

Release the clamped cable ( item 2 ) from the Display Support (item 5).

Step 7.

Disconnect the LVDS Cable (item 3) from the Display Interface Board Assembly.

Step 8.

Disconnect the Backlight Cable (item 4) from the Display Interface Board Assembly.

Step 9.

Carefully remove the Display Support with the LCD (item 5) from the Front Panel.

NOTE

When removing the Display Support (item 5), release the hook (flat cable side) of the
Display Support first (item 6), and then carefully release the other hooks of the Display
Support (item 7).

NOTE

Be careful not to break the hooks.

Replacement Procedure

Step 1.

Reverse the order of the removal procedure.

Содержание E4981A

























































































































































Результаты поиска

Содержание E4981A

Отзывы:

Похожие инструкции для E4981A

Бренды по названию

Популярные бренды

Keysight Technologies E4981A, Руководство по обслуживанию

Результаты поиска

Содержание E4981A

Отзывы:

Похожие инструкции для E4981A

Бренды по названию

Популярные бренды