Keysight Technologies E4981A Скачать руководство пользователя страница 130 | Manualshive

Страница: 130 / 152

background image

128

Chapter 7

Post-Repair Procedures

Post-Repair Procedures

Post-Repair Procedures

Post Repair Procedures

lists the required procedures that must be performed

after the replacement of an assembly. These are the recommended minimum procedures to
ensure that the replacement is successfully completed.

Table 7-1

Post-Repair Procedures

Replaced

Assembly or Part

Required Adjustments

Correction Constants (CC)

Verification

P1001
INSTALLED OS
(E4980-62004)

Perform the following required
adjustments using “PPMC” in Spot
Adjustment of the program.

Power On Test Limit

Inspect the booting process, and power on
test result.

A31 Digital Board

Perform the following required
adjustments using “Write ID” in Spot
Adjustment of the program.

Write ID

Inspect the booting process, and power on
test result.

A34 Analog Board

Perform the following required
adjustments using “A34 Board” in Spot
Adjustment of the program.

Write Null phase track default data
Null DC offset Adjustment
Null ADC DC offset Adjustment
ADC Linearity Adjustment
DC Bias Adjustment
DC level V monitor Adjustment (for
opt 001)
DC level I monitor Adjustment (for opt
001)
DC Source Adjustment (for opt 001)
DCR Adjustment (for opt 001)
Impedance Adjustment
AC Level monitor Adjustment
OSC Level Adjustment

Inspect the booting process, and power on
test result.

DC Bias V Level Monitor Accuracy Test (for
opt 001)

DC Bias I Level Monitor Accuracy Test (for opt
001)
AC Signal Level Monitor Accuracy Test
Impedance Measurement Accuracy Test
DCR Measurement Accuracy Test (for opt 001)

USB Assembly

No adjustment needed

Inspect the booting process, and power on
test result.

“To Check the Front USB port” on page 56

PSU Assembly

No adjustment needed

Inspect the booting process, and power on
test result.

Fan Assembly

No adjustment needed

Inspect the booting process, and power on
test result.

«
...
128
129
130
131
132
...
»

Содержание E4981A

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для E4981A

Бренд: Aaronia Страницы: 47

Бренд: Camille Bauer Страницы: 11

Бренд: Camille Bauer Страницы: 83

Бренд: Facom Страницы: 42

PowerCross-Laser 8 S

Бренд: LaserLiner Страницы: 64

ClimaHome-Check Plus

Бренд: LaserLiner Страницы: 10

MeterMaster Plus

Бренд: LaserLiner Страницы: 104

Бренд: LaserLiner Страницы: 52

LaserRange-Master T2

Бренд: LaserLiner Страницы: 52

Бренд: LaserLiner Страницы: 5

CombiRangeXtender 40

Бренд: LaserLiner Страницы: 84

SuperCross-Laser 2P

Бренд: LaserLine Страницы: 92

MoistureFinder Compact

Бренд: LaserLine Страницы: 56

LaserRange-Master Gi7 Pro

Бренд: LaserLiner Страницы: 56

Бренд: Laser Tools Страницы: 4

SmartVision-Laser

Бренд: LaserLiner Страницы: 56

Бренд: TA Instruments Страницы: 7

Бренд: Yamaha Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды