Keysight Technologies E4981A Скачать руководство пользователя страница 148 | Manualshive

Страница: 148 / 152

background image

146

Appendix D

Error Messages

Error Messages

O

47

OPEN measurement incomplete

This error occurs when the cable correction OPEN measurement is incomplete.

-321

Out of memory

The E4981A has insufficient memory to perform the requested operation.

P

1080

Power failed

Power unit hardware failure is detected.

Contact Keysight Technology’s Sales and Service Office or the company from which you
purchased the device.

-108

Parameter not allowed

The number of parameters is larger than required by the command. For example, although
the

:CREJ:LIM

command requires one parameter such as “

:CREJ:LIM 3

”, two

parameters are added to give “

:CREJ:LIM 0,3

”.

-112

Program mnemonic too long

The length of the header exceeds 12 characters. (Refer to IEEE488.2,7.6.1.4.1.)

Q

-350

Queue overflow

The queue contains a certain code other than the code that caused this error. This indicates
that an error has occurred due to insufficient space in the queue but has not been recorded.

-400

Query error

A comprehensive Query error has occurred for which the E4981A cannot detect further
details. This code simply indicates the occurrence of a Query error that is defined in
IEEE488.2,11.5.1.1.7 and 6.3.

-410

Query INTERRPUTED

This indicates the status that causes an “INTERRUPTED” Query error. (Refer to
IEEE488.1,6.3.2.3.) This error occurs, for example, when data byte (DAB) or GET is
received after Query but before the response has been completely sent.

-420

Query UNTERMINATED

This indicates the status that causes an “UNTERMINATED” Query error. (Refer to
IEEE488.2,6.3.2.) This error occurs, for example, when the E4981A is specified as a talker
and an incomplete program message is received.

-430

Query DEADLOCKED

This indicates the status that causes a “DEADLOCKED” Query error. (Refer to
IEEE488.2,6.3.1.7.) This error occurs, for example, when both input and output buffers
become full and the E4981A cannot continue processing.

«
...
146
147
148
149
150
...
»

Содержание E4981A

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для E4981A

Бренд: TaiDoc Страницы: 31

Бренд: Kawai Страницы: 70

Бренд: 3nh Страницы: 10

Бренд: Yamaha Страницы: 3

Бренд: QLA Страницы: 18

Бренд: Keithley Страницы: 49

Бренд: Keller Страницы: 6

Бренд: Oceanic Страницы: 152

Бренд: Kaiterra Страницы: 8

Бренд: Kaiterra Страницы: 12

Бренд: PAT Страницы: 57

Бренд: AR Страницы: 8

Бренд: GREISINGER Страницы: 20

Бренд: S+S Regeltechnik Страницы: 32

Бренд: Hanna Instruments Страницы: 28

NOVAplus biogas

Бренд: mru Страницы: 78

3501B1260KG/M010LN

Бренд: PCB Piezotronics Страницы: 10

Бренд: ZIEHL Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды