Keysight Technologies E4981A Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 152

background image

3

Safety Summary

The following general safety precautions must be observed during all phases of operation,
service, and repair of this instrument. Failure to comply with these precautions or with
specific WARNINGS elsewhere in this manual may impair the protection provided by the
equipment. Such noncompliance would also violate safety standards of design,
manufacture, and intended use of the instrument. Keysight Technologies assumes no
liability for the customer’s failure to comply with these precautions.

NOTE

The E4981A complies with INSTALLATION CATEGORY II as well as POLLUTION
DEGREE 2 in IEC61010-1. The E4981A is an INDOOR USE product.

NOTE

The LEDs in the E4981A are Class 1 in accordance with IEC60825-1,

CLASS 1 LED PRODUCT

NOTE

This equipment is MEASUREMENT CATEGORY I (CAT I). Do not use for CAT II, III, or
IV.

NOTE

This equipment is tested with stand-alone condition or with the combination with the
accessories supplied by Keysight Technologies against the requirement of the standards
described in the Declaration of Conformity. If it is used as a system component,
compliance of related regulations and safety requirements are to be confirmed by the
builder of the system.

•

Ground the Instrument

To avoid electric shock, the instrument chassis and cabinet must be grounded with the
supplied power cable’s grounding prong.

•

DO NOT Operate in an Explosive Atmosphere

Do not operate the instrument in the presence of inflammable gasses or fumes.
Operation of any electrical instrument in such an environment clearly constitutes a
safety hazard.

•

Keep Away from Live Circuits

Operators must not remove instrument covers. Component replacement and internal
adjustments must be made by qualified maintenance personnel. Do not replace
components with the power cable connected. Under certain conditions, dangerous
voltage levels may remain even after the power cable has been disconnected. To avoid
injuries, always disconnect the power and discharge circuits before touching them.

•

DO NOT Service or Adjust the Instrument Alone

Do not attempt internal service or adjustment unless another person, capable of
rendering first aid and resuscitation, is present.

•

DO NOT Substitute Parts or Modify the Instrument

To avoid the danger of introducing additional hazards, do not install substitute parts or
perform unauthorized modifications to the instrument. Return the instrument to a
Keysight Technologies Sales and Service Office for service and repair to ensure that

«
...
3
4
5
6
7
...
»

Содержание E4981A

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для E4981A

Бренд: Vectronics Страницы: 4

Бренд: Lutron Electronics Страницы: 13

Universal Analyzers 275E

Бренд: Ametek Страницы: 34

Бренд: Topcon Страницы: 59

Digital Piano CA440

Бренд: Kawai Страницы: 48

Бренд: Young Страницы: 5

SiteHawk SK-6000

Бренд: BIRD Страницы: 69

Бренд: Kawai Страницы: 110

Бренд: HyQuest Solutions Страницы: 25

Бренд: T&D Страницы: 31

Sonic-Pro S6A Series

Бренд: Blue-White industries Страницы: 2

Бренд: FMT Swiss AG Страницы: 24

Бренд: INTERSPIRO Страницы: 76

Бренд: Net2Edge Страницы: 37

Бренд: UNI-T Страницы: 11

Бренд: Ada Страницы: 9

Бренд: EUCOL Страницы: 122

Бренд: S.E. International Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды