Keysight Technologies E4981A Скачать руководство пользователя страница 136

Страница: 136 / 152

134

Appendix B

Firmware Update

Update the E4981A firmware using USB/GPIB interface

Required Equipment

•

E4981A.

•

82357A/B USB/GPIB interface.

•

Personal Computer with I/O Libraries Suite (Windows 2000/XP).

How to update E4981A firmware using USB/GPIB interface

The following is the procedure to update the E4981A firmware using USB/GPIB interface.

Step 1.

Connect the USB/GPIB interface from the USB terminal in your computer to the GPIB
terminal in the E4981A rear panel. Then turn the E4981A on.

Step 2.

Copy the following file from Keysight Technologies web site to the temporary work folder
in your computer’s HDD.

•

fw_upd.exe

Step 3.

Execute the

Command Prompt

on your computer.

Step 4.

Change the current folder to the temporary working folder with the “fw_upd.exe” file
using

command.

Step 5.

Enter

fw_upd.exe GPIB0::17::INSTR

command to execute the firmware update program.

The numerical value of “17” in the command is GPIB address of the E4981A. Then, press
the Enter key.

Step 6.

Wait a few minutes until the command prompt is displayed again.

Step 7.

Press

System

key on the E4981A front panel to check the firmware revision.

Содержание E4981A

























































































































































Результаты поиска

Содержание E4981A

Отзывы:

Похожие инструкции для E4981A

Бренды по названию

Популярные бренды

Keysight Technologies E4981A, Руководство по обслуживанию

Результаты поиска

Содержание E4981A

Отзывы:

Похожие инструкции для E4981A

Бренды по названию

Популярные бренды