Keysight Technologies AC6801B Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 197

background image

USB Configuration

The Keysight IO Libraries are required to control the instrument through the USB interface.

Use a standard USB cable to connect the instrument to the computer. There are no configurable USB
parameters, but you can retrieve the USB connect string using the front panel.

Front Panel

SCPI Command

[Menu] > System > IO > USB

The USB connect string appears.

Not available

The instrument complies with USB Specification 2.0, USBTMC Specification 1.0, and USBTMC-
USB488 Specification 1.0. The maximum data rate is 12.5 Mbps, the vendor ID is 0x0957, and the
product ID values are shown in the table below.

Model

Product ID

AC6801B

0x1A02

AC6802B

0x1B02

AC6803B

0x1C02

AC6804B

0x1D02

GPIB Configuration

The GPIB interface requires the optional GPIB interface board and uses a standard IEEE-488 cable to
connect to the computer.

Each device on the GPIB (IEEE-488) interface must have a unique whole number address between 0
and 30 (default 5). Your computer’s GPIB interface card address must not conflict with any instrument
on the interface bus. To change the GPIB address:

Front Panel

SCPI Command

[Menu] > System > IO > GPIB

Use the numeric keypad to enter a value from 0 to 30. Then press [Enter].

Not available

This setting is nonvolatile; it will not be changed by power cycling or

.

LAN Configuration

The following sections describe the primary front-panel LAN configuration functions. There are no
equivalent SCPI commands.

To begin configuring the remote interface from the front panel, press [Menu] > System > IO > LAN.

1 Getting Started

42

Keysight AC6800B Series Operating and Service Guide

«
...
40
41
42
43
44
...
»

Содержание AC6801B






































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AC6801B

Бренд: LSC Страницы: 8

Бренд: GE Multilin Страницы: 90

LIEBERT MPX BRM

Бренд: Vertiv Страницы: 2

Бренд: Atlas IED Страницы: 16

PLUGMOLD PM48TC

Бренд: LEGRAND Страницы: 2

Бренд: LEGRAND Страницы: 6

Бренд: ICM Controls Страницы: 2

Бренд: Panamax Страницы: 17

VR 5000 noSpool

Бренд: Fronius Страницы: 132

Бренд: ABB Страницы: 24

Power Line Conditioner RLC-900

Бренд: Rotel Страницы: 8

Бренд: Art Страницы: 1

Бренд: Vertiv Страницы: 20

RA5014-515-15A-515

Бренд: Synergy Global Technology Страницы: 5

RA5024-520-20A-L520

Бренд: Synergy Global Technology Страницы: 7

InfraPower IPM-01

Бренд: Synergy Global Technology Страницы: 36

Бренд: Greenlee Страницы: 22

Бренд: Elgar Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды