Keysight Technologies AC6801B Скачать руководство пользователя страница 106

Страница: 106 / 197

Command Quick Reference

ABORt Subsystem

Command/Query Description

ABORt[:ALL]

Aborts both TRANsient and ACQuire operations.

ABORt:ACQuire

Aborts all ACQuire operations.

ABORt:TRANsient Aborts all TRANsient actions.

CALibrate Subsystem

Command/Query

Description

CALibrate:COUNt?

Returns the calibration count.

CALibrate:CURRent:OFFSet <

value

Starts the DC current limit calibration for the specified voltage range.

CALibrate:DATA <

value

Enters the calibration value read from a multimeter.

CALibrate:DATE "<

date

CALibrate:DATE?

Sets the calibration date.

CALibrate:LEVel P1|P2|P3|P4|P5

Advances to the next calibration point.

CALibrate:PASSword "<

password

Sets the Admin password, which is used for calibration.

CALibrate:SAVE

Saves the calibration data and date, not the administration password, into nonvolatile
memory.

CALibrate:STATe ON|1|OFF|0 [,<pass-
word>]
CALibrate:STATe?

Enables or disables calibration mode.

CALibrate:VOLTage[:LEVel] <

value

Selects the AC voltage range to calibrate.

CALibrate:VOLTage:OFFset <

value

Selects the DC voltage range to calibrate.

CURRent Subsytem

Command/Query

Description

[SOURce:]CURRent[:LEVel][:IMMediate][:AMPLitude] <

value

>|MINim-

um|MAXimum
[SOURce:]CURRent[:LEVel][:IMMediate][:AMPLitude]? [MINimum|MAXimum]

Sets the immediate AC current limit in amps
(rms).

[SOURce:]CURRent:OFFSet[:IMMediate] <

value

>|MINimum|MAXimum

[SOURce:]CURRent:OFFSet[:IMMediate]? [MINimum|MAXimum]

Sets the immediate DC current limit in amps.

[SOURce:]CURRent:PROTection:STATe ON|1|OFF|0
[SOURce:]CURRent:PROTection:STATe?

Enables or disables current protection.

3 SCPI Programming Reference

106

Keysight AC6800B Series Operating and Service Guide

Содержание AC6801B






































































































































































































Результаты поиска

Содержание AC6801B

Отзывы:

Похожие инструкции для AC6801B

Бренды по названию

Популярные бренды

Keysight Technologies AC6801B, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание AC6801B

Отзывы:

Похожие инструкции для AC6801B

Бренды по названию

Популярные бренды