manualshive.com logo in svg

KEPCO KLP 10-150-1.2K, Руководство пользователя

Пользовательский мануал для KEPCO KLP 10-150-1.2K доступен бесплатно для загрузки с нашего сайта. В этом руководстве содержится вся необходимая информация о продукте. Скачать его можно с {вебсайта}. Не упустите возможность облегчить использование этого продукта!

Поделиться
Скачать
background image

2-14

KLP-HV 031308

2.7.9

ANALOG I/O CONNECTIONS

The Analog I/O Port connector, located on the rear panel of the KLP power supply (see Figure
2-2), provides access for all analog programming inputs and status signal outputs. In addition,
an external trigger input is available for use with SCPI *TRG and TRIG commands. Refer to
Table 2-7 for analog I/O programming signal pin assignments and descriptions.

These signals must be protected from radiated and conducted noise as well as from physical
contact with non-valid driving sources. The following subsections address specific programming
signal applications; in general, however, when accessing this connector from distant locations
or high-noise environments, it is recommended that a shielded cable be used, with the shield
terminated to the system's single point ground. 

a. Analog Programming Enable (ANALOG_CTRL)

Connect pin 12 (Analog Control) to pin 9, 11, 13, or 15 (ground) to enable analog I/O pro-
gramming.

b. External Voltage and Current Programming (V_Ref and C_Ref) 

Twist the voltage programming signal V_Ref (pin 3), Current Programming signal C_Ref (pin
1) and ground (pin 9, 11, 13, or 15). Configure Analog I/O switch positions 1 and 2 to use
either voltage or resistance as the programming source. Factory default for full scale output
is 10V or 10 Kohms (see par. 4.3.3 to set lower values for full scale output).

c. Voltage and Current Readback (VOLT_RBACK and CURR_RBACK)

Twist the voltage readback signal VOLT_RBACK (pin 6), Current readback signal
CURR_RBACK (pin 7) together with ground (pin 9, 11, 13, or 15). Full scale readback volt-
ages are identical to selected full scale programming voltages (see PAR. 4.3.3). 

d. Remote Inhibit (REM_INH)

Twist remote inhibit (pin 8) together with ground (pin 9, 11, 13, or 15). See PAR. 3.2.13.5.1 to
configure active high or low and PAR. 3.4.1 to enable/disable the output using remote inhibit.

e. Fault Connections (RELAY_NC, RELAY_COM, RELAY_NO

It is recommended that normally open and normally closed relay signals RELAY_NC (pin 10)
and/or RELAY_NO (pin 2), respectively, be twisted together with RELAY_COM (pin 4) as
needed to eliminate noise pickup. See PAR. 3.2.13.3 to configure internal relay.

f. External Trigger (EXT_TRIG)

External Trigger may be used with the SCPI TRIG commands (see KLP Developer’s Guide)
during digital remote operation. For noise suppression it is recommended that wires from
EXT_TRIG, pin 14 and ground (pin 9, 11, 13, or 15) be twisted together. 

2.8

DIGITAL CONNECTIONS

The following paragraphs describe the connections required to use the GPIB, RS 232 [-1200
Models only] or LAN [-1.2K models only] ports for remote control of the unit.

2.8.1

GPIB CONNECTIONS

Your computer must have a GPIB interface card installed. Connect the power supply to the
computer’s GPIB interface card. Use a standard GPIB interface cable at the GPIB port on the
rear panel (See Figure 2-2). Refer to Table 2-3 for GPIB port pin assignments. Refer to PAR.
3.2.9 to change the default GPIB address (6) from the front panel. 

Содержание KLP 10-150-1.2K





















































































Отзывы:

Нет отзывов

Похожие инструкции для KLP 10-150-1.2K

Fayat Group Bomag BPR 70/70 D Operating Instructions, Maintenance Instructions preview
Bomag BPR 70/70 D
Бренд: Fayat Group Страницы: 74
Fayat DYNAPAC DFP8 Operating Instructions And Maintenance preview
DYNAPAC DFP8
Бренд: Fayat Страницы: 110
Fayat Bomag BPR 25/40 Operating Instructions, Maintenance Instructions preview
Bomag BPR 25/40
Бренд: Fayat Страницы: 57
Badger Welder B22 Operation Manual preview
B22
Бренд: Badger Welder Страницы: 6
Nordson Standard iControl Instruction Sheet preview
Standard iControl
Бренд: Nordson Страницы: 6
US SAWS Tuc-Pointer Manual preview
Tuc-Pointer
Бренд: US SAWS Страницы: 4
U.S. General 54425 Assembly And Operating Instructions Manual preview
54425
Бренд: U.S. General Страницы: 10
Fein AFMM 14 Repair Instructions preview
AFMM 14
Бренд: Fein Страницы: 25
microjig GRR-RIPPER Instructional Manual preview
GRR-RIPPER
Бренд: microjig Страницы: 22
Fein Sheet Metal Shear BLs 2.5 Parts List preview
Sheet Metal Shear BLs 2.5
Бренд: Fein Страницы: 3
SLAT ACCES Operating Instructions Manual preview
ACCES
Бренд: SLAT Страницы: 36
P.I.T. PMT20H-035A User Manual preview
PMT20H-035A
Бренд: P.I.T. Страницы: 24
WAREMA GA Standard Operating And Installation Instructions preview
GA Standard
Бренд: WAREMA Страницы: 4
Draper CS36L Instructions For preview
CS36L
Бренд: Draper Страницы: 12
Palmgren 9680130 Operating Manual & Parts List preview
9680130
Бренд: Palmgren Страницы: 46
SATA 96411 User Manual preview
96411
Бренд: SATA Страницы: 74
Stanley LaBounty MRP Safety, Operation & Maintenance Instructions preview
LaBounty MRP
Бренд: Stanley Страницы: 24
Kolver 110003/FR Operator'S Handbook preview
110003/FR
Бренд: Kolver Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды