manualshive.com logo in svg

KEPCO BOP 1000W, Руководство оператора

Операторское руководство KEPCO BOP 1000W - полезное руководство для управления мощным источником питания. Скачайте его бесплатно с нашего сайта, чтобы получить всю необходимую информацию о продукте. Необходимая помощь для эффективной работы с KEPCO BOP 1000W ждет вас на manualshive.com.

Поделиться
Скачать
background image

BOP-1K 080709

B-27

B.98 [SOURce:]VOLTage[:LEVel]:PROTect:NEGative COMMAND 

VOLT:PROT:NEG

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:PROT:NEG <exp_value>
Long Form: [SOURce:]VOLTage[:LEVel]:PROTect:NEGative <exp_value>
where <value> is between minimum (box) value (Figure 1-3) and 1% above rated (nominal) output
voltage.

Description: Establishes the negative protection limit for voltage; maximum is 1% greater than rated output voltage.

B.99 [SOURce:]VOLTage[:LEVel]:PROTect:NEGative? QUERY 

VOLT:PROT:NEG?

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:PROT:NEG?
Long Form: [SOURce:]VOLTage[:LEVel]:PROTect:NEGative?
Returns: <exp_value>

Description: Identifies the negative protection limit for voltage.

B.100 [SOURce:]VOLTage[:LEVel]:PROTect:POSitive COMMAND 

VOLT:PROT:POS

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:PROT:POS <exp_value>
Long Form: [SOURce:]VOLTage[:LEVel]:PROTect:POSitive <exp_value>
where <value> is between minimum (box) value (Figure 1-3) and 1% above rated (nominal) output
voltage.

Description: Establishes the positive protection limit for voltage; maximum is 1% greater than rated output voltage.

B.101 [SOURce:]VOLTage[:LEVel]:PROTect:POSitive? QUERY 

VOLT:PROT:POS?

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:PROT:POS?
Long Form: [SOURce:]VOLTage[:LEVel]:PROTect:POSitive?
Returns: <exp_value>

Description: Identifies the positive protection limit for voltage.

B.102 [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:BOTH COMMAND

VOLT:PROT:LIM[:BOTH]

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:PROT:LIMit[:BOTH] <value>
Long Form: [SOURce:]VOLTage[:LEVel]:PROTect:LIM[:BOTH <value>
where <value> is between minimum (box) value (Figure 1-3) and 1% above rated (nominal) output
voltage.

Description: Establishes the maximum value possible for both the positive and negative protection limits for volt-

age. Requires MEM:UPD (PAR. B.12) to save for power up. See PAR. 3.5.2.2 and Figure 3-16 for spe-
cial programming considerations.

B.103 [SOURce:]VOLTage[:LEVel]:PROTect:LIMit[:BOTH]? QUERY 

VOLT:PROT:LIM[:BOTH]?

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:PROT:LIM[:BOTH]?
Long Form: [SOURce:]VOLTage[:LEVel]:PROTect:LIMit[:BOTH]?
Returns <exp_value>,<exp_value>

Description: Identifies the maximum value possible for protection limits for voltage (positive, negative); maximum is

1% greater than rated output voltage. 

B.104 [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:NEGative COMMAND

VOLT:PROT:LIM:NEG

Syntax:

Short Form: [SOUR:]VOLT[:LEV]:PROT:LIM:NEG <exp_value>
Long Form: [SOURce:]VOLTage[:LEVel]:PROTect:LIMit:NEGative <exp_value>
where <value> is between minimum (box) value (Figure 1-3) and 1% above rated (nominal) output
voltage.
Description:Establishes the minimum (maximum absolute) value possible for the negative protection
limit for voltage. This may be set up to 1% greater than rated voltage. Requires MEM:UPD (PAR.
B.12) to save for power up. See PAR. 3.5.2.2 and Figure 3-16 for special programming consider-
ations.

Содержание BOP 1000W





























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BOP 1000W

Rapid 100E Operator'S Manual preview
100E
Бренд: Rapid Страницы: 6
Davey Water Products D75 Installation And Operating Instrictions preview
D75
Бренд: Davey Water Products Страницы: 4
E-Lite 600N Installation & Adjustment Instructions preview
600N
Бренд: E-Lite Страницы: 4
National Flooring Equipment 5700 Operating & Service Manual preview
5700
Бренд: National Flooring Equipment Страницы: 49
National Flooring Equipent 5700 Service Manual preview
5700
Бренд: National Flooring Equipent Страницы: 33
OMCN 6040 Use And Maintenance Instructions preview
6040
Бренд: OMCN Страницы: 13
WABCO OptiTire Installation Manual preview
OptiTire
Бренд: WABCO Страницы: 24
yellow jacket 60242 Flaring Instructions preview
60242
Бренд: yellow jacket Страницы: 2
Landoll EHP Operator'S Manual preview
EHP
Бренд: Landoll Страницы: 54
Nakayama ES2001 Translation Of The Original Instructions preview
ES2001
Бренд: Nakayama Страницы: 101
GEM PSU320-12 Manual preview
PSU320-12
Бренд: GEM Страницы: 2
SilverStone ST400 STRIDER User Manual preview
ST400 STRIDER
Бренд: SilverStone Страницы: 12
Senco WC330-SP Operating Instructions Manual preview
WC330-SP
Бренд: Senco Страницы: 32
Ryobi EJS700RG Owner'S Operating Manual preview
EJS700RG
Бренд: Ryobi Страницы: 13
EINHELL GC-CG 3,6 Li WT Original Operating Instructions preview
GC-CG 3,6 Li WT
Бренд: EINHELL Страницы: 72
Eaton Power Xpert Series Installation And Operation Manual preview
Power Xpert Series
Бренд: Eaton Страницы: 156
REMS Akku-Press 22 V ACC Instruction Manual preview
Akku-Press 22 V ACC
Бренд: REMS Страницы: 212
Kyocera TJEP KA 4060 GAS 3G Quick Start Manual preview
TJEP KA 4060 GAS 3G
Бренд: Kyocera Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды