KEPCO BOP 1000W Скачать руководство пользователя страница 62

Страница: 62 / 188

2-24

BOP HIPWR 080709

2.8.5

RESTORING A UNIT TO STANDALONE OPERATION

1. Turn off power to the master.

2. Turn off power to the slave(s).

3. Turn on power to the unit to be restored to standalone operation.

4. From the power-up screen press

to enter the General Setup Menu. Highlight

Series/

Parallel

and press

to view the Multiple Units menu (see Table 2-12). When prompted,

enter ADMIN2 password (see PAR. 3.2.4.4) before continuing.

5. Press

to return to factory defaults. This configures the unit as a standalone unit.

6. Press

to save for power-up.

7. Turn off power to the unit, then turn power on. The unit will power up as a standalone unit.

2.8.6

CHANGING MULTIPLE UNIT CONFIGURATIONS

To change a unit from series, parallel, Master 2X2 or Master 3X2 operation to a different config-
uration, first set the unit to Standalone by referring to PAR. 2.8.5, then refer to PAR. 2.8.3 and
configure as desired.

Содержание BOP 1000W





























































































































































































Результаты поиска

Содержание BOP 1000W

Отзывы:

Похожие инструкции для BOP 1000W

Бренды по названию

Популярные бренды

KEPCO BOP 1000W, Руководство оператора

Результаты поиска

Содержание BOP 1000W

Отзывы:

Похожие инструкции для BOP 1000W

Бренды по названию

Популярные бренды