KEPCO BOP 1000W Скачать руководство пользователя страница 153 | Manualshive

Страница: 153 / 188

background image

BOP-1K 080709

B-3

B.5

INITiate[:IMMediate] COMMAND

INIT[:IMM]

Syntax:

Short Form: INIT:[IMM] Long Form: INITiate[:IMMediate]

Description:

Enables a single trigger.

This command enables a single trigger. A *TRG command completes the

sequence, however TRIG:SOUR (see PAR. B.145) must be set to BUS. Upon receipt of the *TRG
command, the power supply will return to the commanded values of voltage and current established
by the VOLT:TRIG and CURR:TRIG commands. After a *TRG command has been received, subse-
quent *TRG commands have no effect unless preceded by INIT or INIT:CONT ON. Related Com-
mands: *TRG, TRIG, TRIG:SOUR. (See example, Figure B-1.)

FIGURE B-1. PROGRAMMING THE OUTPUT

CAL:CEXT command
CAL:CGA command
CAL:CLIM command
CAL:CPR command
CAL:CURR[:DATA] command
CAL:DATA value command
CAL:DPOT command
CAL:SAVE command

CAL:STAT command and query
CAL:VEXT command
CAL:VGA command
CAL:VLIM command
CAL:VOLT[:DATA] command
CAL:VPR command
CAL:ZERO command

NOTES: 1. The power supply is assumed to be operating in constant voltage mode.

2 Examples below are intended only to illustrate command functions. Refer to PAR. 3.5.2 for pro-

gramming techniques to optimize performance.

OUTP ON

Turns the output on.

VOLT 21; CURR 1.5

Power supply output programmed to go to 21V, current limit 1.5A

INIT:CONT ON

Continuous triggers enabled.

INIT:CONT?

Power supply returns “1.”

TRIG:SOUR BUS

Prepare unit to wait for *TRG.

VOLT:TRIG 15;CURR:TRIG 3

Power supply output programmed to return to 15V, current limit
3A upon receipt of trigger.

*TRG

Power supply output returns to 15V,current limit 3A.

VOLT 21; CURR 5E-2

Power supply output programmed to go to 21V, current limit 0.05A

MEAS:VOLT?

If actual value of output voltage is 20.99V, power supply
returns 2.099E1 within the limits of readback accuracy.

MEAS:CURR?

If actual value of output current is 0.0499A, power supply
returns 4.99E-2 within the limits of readback accuracy.

FUNC:MODE CURR

Establishes constant current mode as power supply operating mode.

VOLT 21; CURR 1.1

Power supply programmed to voltage limit 21V, 1.1A.

CURR?

Returns 1.1.

FUNC:MODE VOLT

Establishes constant voltage mode as power supply operating mode.

CURR:TRIG?

Returns 3 (current value established by CURR:TRIG).

VOLT:TRIG?

Returns 15 (voltage value established by VOLT:TRIG).

*TRG

Power supply output returns to 15V, current limit 3A.

INIT:CONT 0

Triggers disabled.

INIT:CONT?

Power supply returns “0.”

VOLT 0

Power supply output programmed to go to 0V.

MEAS:VOLT?

Returns 0 within the limits of readback accuracy (measured output
voltage).

VOLT?

Returns 0 within the limits of readback accuracy (programmed output
voltage).

CURR?

Returns 3 (programmed current).

MEAS:CURR?

Returns 0 within the limits of readback accuracy (measured output
current)

«
...
151
152
153
154
155
...
»

Содержание BOP 1000W





























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BOP 1000W

Universal Notebook Power Supply

Бренд: Hama Страницы: 24

Бренд: Parkside Performance Страницы: 134

Бренд: Wacker Neuson Страницы: 30

Бренд: TDK-Lambda Страницы: 16

Akku-Press 22 V ACC

Бренд: REMS Страницы: 212

Бренд: Patriot Страницы: 35

Бренд: OLI Страницы: 2

Accelerator 2000

Бренд: Rapid Страницы: 76

Бренд: Kamasa-TOOLS Страницы: 12

Бренд: Campbell Hausfeld Страницы: 10

750-613/040-000

Бренд: WAGO Страницы: 52

Бренд: Timberline Tool Страницы: 8

Бренд: Sharkoon Страницы: 10

Бренд: Valcom Страницы: 2

Бренд: Galaxy Страницы: 11

Бренд: Horizont Страницы: 27

Бренд: CHP Страницы: 8

Бренд: DAJ Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды