KEPCO BOP 1000W Скачать руководство пользователя страница 184

Страница: 184 / 188

B-34

BOP-1K 080709

B.141 SYSTem:SECurity:IMMediate COMMAND

SYST:SEC:IMM

Syntax

Short Form: SYST:SEC:IMM

Long Form: SYSTem:SECurity:IMMediate

Description:

Initializes all NVRAM variable to factory defaults.

Empties all memory locations. See PAR. 3.5.2.2

and Figure 3-16 for special programming considerations. This command is password protected (must
be preceded by SYST:PASS:CEN (see PAR B.135).

B.142 SYSTem:SET COMMAND

SYST:SET

Syntax

Short Form: SYSTem:SET {CM0 | CM1 | DCL0 | DCL1 | LF0 | LF1 | RO0 | RO1}
Long Form: SYSTem:SET {CM0 | CM1 | DCL0 | DCL1 | LF0 | LF1 | RO0 | RO1}

Description:

Establishes Device Clear, Line Feed, OUTP command and Reset functions. Sending
SYST:SEC:IMM sets LF1, DC0, and RO0 (as if CM0 was sent).

Requires MEM:UPD (PAR. B.12) to

save for power up. See PAR. 3.5.2.2 and Figure 3-16 for special programming considerations.
DCL0

Device Clear functions per IEEE 488.2 Standard. (No effect on the device (power supply),
only clears internal status registers.)

DCL1

Device Clear functions identical to *RST (Output set to 0V, voltage mode and output set to
OFF except if RO1 (see below) is set.)

LF0

Line Feed not provided upon empty buffer condition

LF1

Line Feed provided if buffer is empty and a read is performed.

RO0

*RST and power up set output to OFF, 0V, 0A, voltage mode.

RO1

*RST sets output to ON, 0V, 0A, voltage mode. Subsequent VOLT and CURR commands
are immediately present at the output without sending OUTP ON (OUTP OFF and OUTP
ON function normally to turn the output off or on.)

CM0

Establishes DCL0, LF0, RO0 conditions described above. (SCPI 1997 Standard compli-
ance)

CM1

Establishes DCL1, LF1, RO1 conditions described above. (Compatible with software ver-
sions 1.2 and earlier) (See example, Figure B-12.)

B.143 SYSTem:SET? QUERY

SYST:SET?

Syntax

Short Form: SYST:SET?

Long Form: SYSTem:SET?

Return Value: DCL<n>,LF<n>,RO<n> where n = 0 or 1

Description:

Identifies functions established by SYST:SET command.

(See example, Figure B-12.)

B.144 SYSTem:VERSion? QUERY

SYST:VERS?

Syntax

Short Form: SYST:VERS?

Long Form: SYSTem:VERSion?

Return Value: <int_value>.<int_value> (YYYY.V)

Description:

Identifies SCPI Version implemented.

Returns SCPI Version number:

YYYY = year, V = Revision number for specified year. (See example, Figure B-12.)

FIGURE B-12. USING SYSTEM COMMANDS AND QUERIES

SYST:VERS?

Unit returns 1997

SYST:SET?

Unit returns DC0,LF0,RL0,OUT0

SYST:PASS:NEW DEFAULT,OKAY

Unit changes password to be OKAY

SYST:SET LF1,RL1,DC1

Configures Device Clear, Line Feed and Reset
(see PAR. B.142).

SYST:PASS:CEN OKAY

Password enabled commands are accepted

MEM:UPDATE INTERFACE

Unit saves the LF1 state for next power on cycle.

Содержание BOP 1000W





























































































































































































Результаты поиска

Содержание BOP 1000W

Отзывы:

Похожие инструкции для BOP 1000W

Бренды по названию

Популярные бренды

KEPCO BOP 1000W, Руководство оператора

Результаты поиска

Содержание BOP 1000W

Отзывы:

Похожие инструкции для BOP 1000W

Бренды по названию

Популярные бренды