KEPCO BOP 1000W Скачать руководство пользователя страница 183

Страница: 183 / 188

BOP-1K 080709

B-33

B.134 SYSTem:KEYBoard? QUERY

SYST:KEYB?

Syntax:

Short Form: SYST:KEYB?

Long Form: SYSTem:KEYBoard?

Returns: 1 or 0
Description:Identifies the state of the keypad: locked (1) or unlocked (0).

B.135 SYSTem:PASSword:CENable COMMAND

SYST:PASS:CEN

Syntax

Short Form: SYST:PASS:CEN <val>
Long Form: SYSTem:PASSword:CENable <val>

Description: Sets the password enable state if the value matches the current Main password. This command

allows CALibrate commands to operate.

B.136 SYSTem:PASSword:CDISable COMMAND

SYST:PASS:CDIS

Syntax

Short Form: SYST:PASS:CDIS

Long Form: SYSTem:PASSword:CDISable

Description: Clears the password enable state.

B.137 SYSTem:PASSword:NEW COMMAND

SYST:PASS:NEW

Syntax

Short Form: SYST:PASS:NEW <old password>,<new password>
Long Form: SYSTem:PASSword:NEW <old password>,<new password>

Description:

Establishes new password.

The old (current) Main password is checked, then replaced by the new

password. Admin 1 and 2 passwords (PAR. 3.2.4.3) are not available. (See example, Figure B-12.)
See PAR. 3.5.2.2 and Figure 3-16 for special programming considerations.

B.138 SYSTem:PASSword:STATe? QUERY

SYST:PASS:STAT?

Syntax

Short Form: SYST:PASS:STAT?

Long Form: SYSTem:PASSword:STATe?

Return Value: <int_value> 0 or 1

Description: Returns a 1 if the password state is enabled or a 0 if it is disabled.

B.139 SYSTem:REMote

COMMAND

SYST:REM

Syntax

Short Form: SYST:REM {ON | OFF} or {1 | 0}
Long Form: SYSTem:REMote {ON | OFF} or {1 | 0}

Description:

Used during serial (RS 232) communication to set the unit to remote (1 or ON) or local (0 or
OFF) mode.

This command must be issued prior to commands that affect the power supply output

(e.g., VOLT 10;:OUTP ON) to ensure the unit is in remote mode. See PAR. 3.5.6.3 and Figure B-11.

B.140 SYSTem:REMote? QUERY

SYST:REM?

Syntax

Short Form: SYST:REM?

Long Form: SYSTem:REMote?

Return Value: {1 | 0}

Description:

Identifies whether unit it in remote mode (1) or local mode (0) during serial (RS 232) communi-
cation.

See PAR. 3.5.6.3 and Figure B-11.

FIGURE B-11. SETTING THE UNIT TO REMOTE MODE VIA SERIAL (RS 232) PORT

*IDN?

Unit responds with KEPCO,BOP 50-20,E1234,1.66 (typical).

outp?

Unit responds with 0 indicating output is off

syst:rem?

Unit responds with 0 indicating unit is in local mode.

syst:rem 1

Puts unit in remote mode.

outp on

Enables output

outp?

Unit responds with 1 (output on).

syst:rem 0

Unit set to local mode.

Содержание BOP 1000W





























































































































































































Результаты поиска

Содержание BOP 1000W

Отзывы:

Похожие инструкции для BOP 1000W

Бренды по названию

Популярные бренды

KEPCO BOP 1000W, Руководство оператора

Результаты поиска

Содержание BOP 1000W

Отзывы:

Похожие инструкции для BOP 1000W

Бренды по названию

Популярные бренды