background image

            

9.6.

Configuration and operation modes

The access system Kentix DoorLock can be operated in an online- and offline-mode.
In the offline-mode the complete programming is done at each DoorLock-device separately.

Time profiles cannot be configured in this mode. The offline-mode is suitable for small installations with only a 
few doors and up to 10 users.

In the online-mode the programming of DoorLock-devices is done via the web-interface of the AccessPoints. 
Here only the master card set (Servicekey) has to be programmed directly at the device.

9.6.1.

DoorLock-device without AccessPoint (offline-mode)

The programming basically consists of two steps:

the initial setup and the programming of the RFID cards for the users.

9.6.1.1.

Initial setup - insert / activate batteries

Online knob and door lever and cabinet lock are battery operating devices. For the commissioning the batteries 
must be inserted or activated first.
The

 Online knob

 is delivered in opened state with the a loosely mounted knob cover.

The cover can be easily pulled down from the knob. One of the two batteries is blocked by a plastic lock. This 
lock has to be pulled out to activate the knob. The knob then signalizes the activation by multiple short tones.

At the 

Online door lever

 the required battery is not installed, but delivered with the additional equipment.

To insert the battery, the allen screw on the electronic side must be 

screwed into

 the lever using the enclosed 

Allen key. The front part can then simply be removed.

Insert the battery with the negative pole first into the front part. Then put it back onto the lever and fasten it.

The activation is then signalized by a short tone.

At the 

Online cabinet lock

 the battery is also delivered separately. It has to be inserted into the battery 

compartment which is then pushed into the lock from below.
For the opening a special key is required which has to be purchased separately.

Page 

                                                               (07-2018, subject to change)

kentix.com

74

NOTE!

Each action is confirmed by visual and acoustic notifications. 

  

   

       

Sm

a

rt 

A

c

c

e

s

s

     

Содержание AlarmManager-BASIC


































































































































Отзывы: