K2 Conservatories TGBv6.1 Скачать руководство пользователя | Manualshive

Страница: 51 / 73

background image

Page 51

Garden Building

Installation Guide

Product Code : TGBv6.1 / November 2011

Octagonal Garden Building Models

Position  the  triangular  roof  glazing  sheets
between  the  roof  glazing  bars  allowing  an
even  gap  between  the  edge  of  the  roof
glazing sheets and the roof bars.

Recommended Method of Glazing

When  you  are  glazing  your  conservatory
roof  it  is  recommended  that  you  place  the
roof  glazing  sheet  labelled  ‘G1’into  position
first.  Then  by  use  of  a  step  ladder  through
the  empty  ‘G2’  roof  glazing  sheet  position
you will have good access to put on the spar
top  cap  labelled  ‘P1’  first.  Then  place  ‘G2’
roof glazing sheet into position whilst getting
good  access  to  put  on  ‘P2’  spar  top  cap by
use of your stepladder in the empty ‘G3’ roof
glazing sheet position.

If  you  choose  to  install  the  roof  glazing
sheets  and  glazing  bar  top  caps  in  this  way
it  is  imperative  that  you  read  both  the
Glazing Installation and the Glazing Bar
Installation  sections  prior  to  glazing  your
conservatory roof.

When  satisfied  that  the  roof  glazing  sheets
are  in  place,  gently  pull  on  the  glazing  tape
protective  film  on  the  eaves  beam  closure
situated  in  the  eaves  beam  (A5080)  in  a
downwards  motion  while  pressing  firmly
down on the roof glazing sheet to make sure
that  it  remains  in  position  afterwards.
Continue  to  fit  all  others  as  previously
described.

PLEASE  NOTE  IT  IS  NOT  UNCOMMON  FOR
CONDENSATION TO APPEAR IN THE FLUTES
OF  THE  POLYCARBONATE  ROOF  GLAZING
SHEETS FROM TIME TO TIME.

THE  ‘BREATHER’  TAPE  PRE-FITTED  TO  THE
BOTTOM  OF  THE  POLYCARBONATE  ROOF
GLAZING  SHEETS  IS  DESIGNED  TO  ALLOW
THE

MOISTURE

TO

EVAPOURATE

NATURALLY.

DO NOT BREAK THE SEAL ON THE
BREATHER

TAPES

IN

ATTEMPT

TO

INCREASE THE VENTILATION INTO THE
FLUTES OF THE POLYCARBONATE ROOF
GLAZING SHEETS.

«
...
49
50
51
52
53
...
»

Содержание TGBv6.1










































































Отзывы:

Нет отзывов

Похожие инструкции для TGBv6.1

Бренд: Palmako Страницы: 38

BYGNORDIC Torun 400x300 28

Бренд: XL-BYG Страницы: 8

Бренд: Shire Страницы: 22

HomePlace Bungalow

Бренд: Suncast Страницы: 42

Бренд: E-Z FRAME Страницы: 6

Бренд: Palmako Страницы: 84

Бренд: Palmako Страницы: 43

Бренд: Palmako Страницы: 102

Бренд: Palmako Страницы: 54

Tomas FR34-3857-2

Бренд: Palmako Страницы: 115

Бренд: GARDY SHELTER Страницы: 137

Бренд: GARDY SHELTER Страницы: 185

White Wood FRJ40-4040

Бренд: Palmako Страницы: 56

Бренд: Keter Страницы: 62

Бренд: Universo Consumer Products Страницы: 20

Бренд: OSTO Страницы: 17

Бренд: Duratuf Страницы: 42

Бренд: Albany Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды