K2 Conservatories TGBv6.1 Скачать руководство пользователя | Manualshive

Страница: 49 / 73

background image

Page 49

Garden Building

Installation Guide

Product Code : TGBv6.1 / November 2011

The  glazing  end  trim  push  fits  over  the
bottom  edge  of  the  roof  glazing  sheet  with
the  flange  facing  downwards  as  shown
below.

Select  the  first  roof  glazing  sheet  and
remove its protective outer film.

It  is  recommended  that  only  a  100mm
perimeter  of  the  inner  protective  film  is
removed  at  this  stage  of  conservatory
installation  as  this  will  help  protect  the  roof
glazing  sheet  from  any  unnecessary
damage.    The  inner  protective  film  can  be
completely removed once  all plaster work is
complete.

Start with the roof glazing sheets against the
wall and to the left with the face that had the
printed  film  facing  outwards.  This  first  sheet
will be labelled as ‘G1’.

Prior  to  fitting  the  roof  glazing  sheets  it  is
recommended to peel back around 50mm to
100mm  of  the  glazing  tape  protective  film.
This enables adjustments to be made to the
position  of  the  roof  glazing  sheets  without
permanently  sticking  the  entire  roof  glazing
sheet to the eaves beam closure.

«
...
47
48
49
50
51
...
»

Содержание TGBv6.1










































































Отзывы:

Нет отзывов

Похожие инструкции для TGBv6.1

Highclere 10x10

Бренд: Norfolk Greenhouses Страницы: 3

Бренд: Palmako Страницы: 29

Бренд: Palmako Страницы: 138

Бренд: Palmako Страницы: 58

Бренд: Gazebo penguin Страницы: 19

Бренд: Palmako Страницы: 46

Бренд: Palmako Страницы: 56

Бренд: Solid Страницы: 37

Бренд: Karibu Страницы: 35

The ORGANIC GARDEN AOGC15081HC

Бренд: ABSCO SHEDS Страницы: 25

Бренд: ABSCO SHEDS Страницы: 25

Бренд: Werth-Holz Страницы: 17

5x5 Corner Playhouse

Бренд: Walton Страницы: 7

7x7 Corner shed

Бренд: Walton Страницы: 5

Бренд: Karibu Страницы: 34

Бренд: Palmako Страницы: 96

Бренд: Palmako Страницы: 76

Бренд: Sojag Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды