P/N 960-100190RA_Rev. A {EDP #148851}
© 2009, Japan CashMachine Co., Limited
6 - 3
Performance Tests
VEGA-RC™BankNote Recycler
Section 6
•
DIP Switch Test
•
Rear Cover Sensor Test
•
Escrow Sensor Input Test
•
Drum (Stacker) In-Sensor Input Test
•
Flap Sensor Input Test
P
USHBUTTON
F
UNCTION
T
EST
, DIP S
WITCH
T
EST
&
R
EAR
C
OVER
T
EST
For the following three (3) tests, refer to Figure 1-4
on page 1-4 of Section 1 of this Manual for the
location of the VEGA-RC Pushbuttons, Dip
Switch Block, and Rear Access Cover. Refer to
Figure 2-26 on page 2-8 of Section 2 of this Man-
ual for the location of the Rear Cover Sensor.
Pushbutton Function Test
Select Test “
T0
” to perform the Pushbutton Func-
tional Test. This test verifies that each of the four
(4) external VEGA-RC Pushbuttons is functioning
properly. Perform the following steps to verify that
the Display indications shown in Figure 6-5 are
correct:
1. Use Pushbutton “B” or “D” to select Test Zero
(T0).
2. Press Pushbutton “
A
”. The Seven (7) Segment
Display should indicate “
TS
” followed by “
01
”.
3. Press Pushbutton “
B
”. The Seven (7) Segment
Display should indicate “
TS
” followed by “
02
”.
4. Press Pushbutton '
C
'. The Seven (7) Segment
Display should indicate “
TS
” followed by “
03
”.
5. Press Pushbutton '
D
'. The Seven (7) Segment
Display should indicate “
TS
” followed by “
04
”.
6. Press and hold-down Pushbutton “
A
” for three
(3) seconds to return the unit to the Test Selection
Mode.
DIP Switch Test
This Test is used to check that each of the eight (8)
Switches located on the VEGA-RC DIP Switch
Block is operating correctly. This is accomplished
by manually changing each Switch settings on the
DIP Switch Block, and then verifying that a correct
output is presented on the Seven (7) Segment Dis-
play. During the Test the DIP Switches function as
an 8-bit Binary Counter which outputs a decimal
value from 0 to 255 when the equivalent value (in
binary) is set on the DIP Switches.
DIP Switch #1 represents the Least Significant Bit
(LSB) of the counter, while DIP Switch #8 repre-
sents the Most Significant Bit (MSB). The Seven
(7) Segment Display indicates the value in a 2-digit
hexadecimal format range from “00” to “FF”.
The left-side character of the Seven (7) Segment
Display represents a hexadecimal value from “0”
to “F” as set on DIP Switches #5, #6, #7 and #8;
and the right-side character represents a hexadeci-
mal value from “0” to “F” as set on DIP Switches
#1, #2, #3 and #4 (See Figure 6-6 and Table 6-1).
1. Use Pushbutton “B” or “D” to select Test Zero
(T0).
2. Press
Pushbutton
“
A
”. The Seven (7) Segment
Display should indicate “
TS
” followed by “
01
”.
3. On the VEGA-RC DIP Switch, set Switches #1
through #8 OFF. The Seven (7) Segment Display
should indicate “
DS
” followed by “
00
”.
0.5 Seconds
0.5 Seconds
0.5 Seconds
0.5 Seconds
0.5 Seconds
0.5 Seconds
0.5 Seconds
0.5 Seconds
01: When pressing A (Change Display) Button
02: When pressing B (Dispense) Button
03: When pressing C (Restore) Button
04: When pressing D (Retrieve) Button
Figure 6-5
Function Key Test (TS = Test Switch)
Table 6-1
Switch Settings vs. Hex Values
DIP Switch Binary
Setting
Hexadecimal Value Displayed
SW #8, 7, 6, 5
SW #4, 3, 2, 1
0000 0000
0
0
0001 0001
1
1
0010 0010
2
2
0011 0011
3
3
0100 0100
4
4
0101 0101
5
5
0110 0110
6
6
0111 0111
7
7
1000 1000
8
8
1001 1001
9
9
1010 1010
A
A
1011 1011
B
B
1100 1100
C
C
1101 1101
D
D
1110 1110
E
E
1111 1111
F
F
Seven Segment Character Display
LEFT SIDE RIGHT SIDE
SW 1, 2, 3 & 4
SW 5, 6, 7 & 8
Figure 6-6
Typical Display vs. Switch Associations
